675141
3
Zoom out
Zoom in
Previous page
1/20
Next page
3
Technical data
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 V AC ±15% 50 Hz
Max. pre-fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 A
Built-in circuit breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-pole, 16 A
Output relay . . . . . . . . . . . . . . . . . . . . . . . .Make contact - SPST - NO
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Max. 16 A / 3600 W
Control principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ON/OFF
Temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+0/+40°C
Difference/hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.4°C
Economy temperature . . . . . . . . . . . . . . . . . . . . . . .5°C (2-8°C OTD2)
- control voltage signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 V AC
Frost protection temperature . . . . . . . . . . . . . . . . . . . . . .5°C absolute
- control voltage signal via rectifier diode . . . . . . . . . . . . . . .230 V AC
Range limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .min./max.
Sensor fault protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-20°C
Ambient operating temperature . . . . . . . . . . . . . . . . . . . . . . .0/+40°C
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H/84, W/84, D/40 mm
Enclosure rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IP 21
The thermostat is maintenance free.
Classification
The product is a Class II appliance (with reinforced insulation) and
must be connected as follows:
Term. 1: Live (L1) 230 V ±15%, 50/60 Hz
Term. 2: Neutral (L2)
Term. 3–4: Max. load 16 A, 3600 W
MICROLINE electronic thermostat for installation in standard wall
box. The thermostat allows the required temperature to be set within
the range 0-40°C. An LED indicates whether heating is active. The
thermostat is suitable for ELKO and NORWESCO systems S-16, RS-
16 and UNI-10. An extra frame is supplied with the unit.
MICROLINE PRODUCT PROGRAMME
OTN2-1991 with floor sensor
OTN2-1999 with built-in room sensor
OTD2-1999 with built-in room sensor and external limitation sensor
CE MARKING
Applied standards
EN 61000-6-3, EN 61000-6-2, EN 60 730-1 and EN 60730-2-9.
The product may only be used if the complete installation complies
with current directives.
The thermostat must only be installed by an authorised electrician.
If the product has been damaged in any way, e.g. during transport, it
must be inspected and checked by authorised personnel before being
connected to the power supply.
The product carries a manufacturer's warranty if installed in
accordance with these instructions and applicable regulations.
Type OTN2 / OTD2 with room or floor sensor English
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arnold Rak OTD 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arnold Rak OTD 2 in the language / languages: English, German, Polish as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info