675129
2
Zoom out
Zoom in
Previous page
1/8
Next page
cable. Two remaining cores of a multi-core
c
able which, for example, supplies current to
t
he floor heating wires, must not be used. The
switching peaks of such current supply lines
m
ay create interfering signals that prevent
o
ptimum controller function. If a shielded cable
i
s used, the shield must not be earthed but
must be connected to terminal 6. The two-core
c
able must be placed in a separate pipe.
Mounting of thermostat with built-in sensor
(fig. 4)
T
he room sensor is used for comfort
t
emperature regulation in rooms. The
thermostat is mounted on the wall with free air
c
irculation about 1.6 m above the floor.
D
raught, direct sunlight, or any other direct
h
eating outlet must be avoided. No external
sensor is to be connected.
M
ounting of thermostat
1. Release the front cover ONLY by inserting a
small screwdriver into the air grills on both
s
ides of the thermostat (see fig. 1).
D
O NOT open the thermostat by releasing
the four fixing clips on the back.
2. Connect cables according to the diagram
(
fig. 2)
3
. The thermostat is mounted in the wall
socket. The cover and the frame are
r
emounted.
Operation
T
he first time the thermostat is connected, time
and day must be set:
Setting of time (the clock flashes
d
uring setting)
Setting of day (day flashes during
setting)
Programming
See users manual.
Fault location
If the sensor is disconnected or short-circuited,
the heating system is cut out. The sensor can be
checked according to the resistance table fig. 5.
Error codes
E0: Internal error. The thermostat must be
replaced.
E1: Built-in sensor short-circuited or
disconnected.
E2: External sensor short-circuited or
disconnected.
CE marking
According to the following standards,
EMC EN 61000-6-1: 2001, EN 61000-6-3: 2001
LVD: EN 60730-1, EN 60730-2-9
Classification
The product is a class II device (enhanced insu-
lation) and the product must be connected to
the following leads,
Term. 1: Phase (L) 230 V±15%, 50/60 Hz
Term. 2: Neutral (N)
Term. 3–4: Load max. 16A, 3,600W
Environment and recycling
Please help us to protect the
environment by disposing of the
packaging in accordance with the
national regulations for waste
processing.
Recycling of obsolete appliances
Appliances with this label must not be disposed
off with the general waste. They must be
collected separately and disposed off according
to local regulations.
Deutsch
Typ OCC2 ist ein elektronischer Ein/Aus-
T
hermostat mit Temperaturregelung durch einen
e
ingebauten oder extern angebrachten NTC-
F
ühler.
Typ OCC2 ist für Unterputzmontage in einer
W
anddose vorgesehen. Als Zubehör ist eine
U
nterlage für Aufwandmontage erhältlich.
Montage des Fühlers
B
odenfühler: Platzierung in einem gemäß EN
6
1386-1 zugelassenen nichtleitenden
Installationsrohr, das im Boden eingelassen ist
(
Abb. 3). Das Rohr ist am Ende verschlossen
u
nd so hoch wie möglich in der Betonschicht
p
latziert. Das Installationsrohr muss zwischen
den Heizkabelserpentinen zentriert werden.
D
as Fühlerkabel kann mit einem separaten
K
abel bis zu 100 m verlängert werden. Ist das
Verlängerungskabel dünner als H05VV-F, muss
es ebenfalls in einem zwischen Fühlerkabel und
T
hermostat durchgehenden Installationsrohr
v
erlegt werden. Zwei freie Leiter eines
Mehrleiterkabels, das beispielsweise
Bodenheizdrähte mit Strom versorgt, dürfen
n
icht verwendet werden. Die Schaltspitzen einer
d
erartigen Stromversorgung können das Signal
beeinträchtigen und eine optimale
R
eglerfunktion verunmöglichen. Wird ein
a
bgeschirmtes Kabel verwendet, darf die
Abschirmung nicht geerdet werden, sondern ist
a
n Klemme 6 anzuschließen. Das
Zweileiterkabel ist in einem separaten Rohr zu
verlegen.
Montage des Thermostaten für Modelle mit
eingebautem Fühler (Fig. 4)
Der Raumfühler wird für die Regelung der
Komforttemperatur in Räumen verwendet. Der
Thermostat wird an einer Wand mit freier
Luftzirkulation und etwa 1,6 m über dem Boden
montiert. Zugluft, direkter Sonnenschein oder
eine andere direkte Wärmebeeinflussung sollten
vermieden werden. Ein externer Fühler soll nicht
angeschlossen werden.
Montage des Thermostaten
1.Einen Schraubenzieher in den Luftgittern auf den
beiden Seiten des Thermostaten einstecken und
den Deckel dadurch lösen (siehe Abb. 1). Der
Thermostat darf nicht durch Lösen der vier
Schnappschlösse hinten geöffnet werden.
2. Kabel anschließen laut Diagramm (Fig. 2)
3. Den Thermostaten in der Wanddose montieren.
Deckel und Rahmen wieder anmontieren.
Inbetriebnahme
Beim ersten Anschluss des Thermostaten
werden Zeit und Tag eingestellt:
Einstellung von Zeit (die Uhr blinkt
während der Einstellung)
Einstellung von Tag (Tag blinkt
während der Einstellung)
Programmierung
Siehe Benutzeranleitung.
Fehlersuche
Falls der Fühler ausgeschaltet oder
kurzgeschlossen ist, wird die Wärmeanlage
ausgeschaltet. Der Fühler kann laut der Wider-
standstabelle in Fig. 5 kontrolliert werden.
Fehlercodes:
E0: Interner Fehler. Der Thermostat muss
ausgewechselt werden.
E1: Der eingebaute Fühler ist kurzgeschlossen
oder ausgeschaltet.
E2: Der externe Fühler ist kurzgeschlossen oder
ausgeschaltet.
CE-Markierung
L
aut folgenden Standards:
E
MC: EN 61000-6-1: 2001, EN 61000-6-3: 2001
LVD: EN 60730-1, EN 60730-2-9
K
lassifikation
D
as Produkt ist ein Klasse II Gerät
(verstärkte Isolierung) und das
P
rodukt muss an folgende Leiter
a
ngeschlossen werden:
Term. 1: Phase (L) 230 V ±15%,
50/60 Hz
T
erm. 2: Null (N)
T
erm. 3–4: Belastung max. 16A, 3.600W
U
mwelt und Wiederverwertung
B
itte helfen Sie uns, die Umwelt zu schützen, und
e
ntsorgen Sie die Verpackung gemäß den natio-
nalen Vorschriften über die Abfallverwertung.
E
ntsorgung von Altgeräten in Deutschland
Geräte mit dieser Kennzeichnung gehören nicht
in die Restmülltonne und sind getrennt zu
s
ammeln und zu entsorgen.
êÛÒÒÍËÈ
àÁ‰ÂÎË éëë2 Ô‰ÒÚ‡‚ÎflÂÚ ÒÓ·ÓÈ
˝
ÎÂÍÚÓÌÌ˚È ÚÂÏÓÒÚ‡Ú ‰Îfl „ÛÎËÓ‚‡ÌËfl
Ú
ÂÏÔÂ‡ÚÛ˚ ÔÛÚÂÏ ‚Íβ˜ÂÌËfl/ÓÚÍβ˜ÂÌËfl
̇„ÛÁÍË ÔË ÔÓÏÓ˘Ë ‚ÒÚÓÂÌÌÓ„Ó ËÎË
˚ÌÓÒÌÓ„Ó ‰‡Ú˜Ë͇ ÓÚˈ‡ÚÂθÌÓ„Ó
ÚÂÏÔÂ‡ÚÛÌÓ„Ó ÍÓ˝ÙÙˈËÂÌÚ‡ NTC.
àÁ‰ÂÎË éëë2 ÔËÒÔÓÒÓ·ÎÂÌÓ ‰Îfl ÒÍ˚ÚÓ„Ó
Ï
ÓÌڇʇ „ÌÂÁ‰Â ÓÁÂÚÍË. ÇÓÁÏÓÊÂÌ
ÓÚÍ˚Ú˚È Ì‡ÒÚÂÌÌ˚È ÏÓÌÚ‡Ê ÔË ÔÓÏÓ˘Ë
ÒÔˆˇθÌÓ„Ó ÍÂÔÎÂÌËfl.
ВНИМАНИЕ: Меры предосторожности
Изолируйте концы питания перед установкой
или при проведении регламентных работ по
обслуживанию устройства и его
компонентов.
Данный прибор и его компоненты должны
устанавливаться аттестованным
персоналом (напр. квалифицированным
электриком). Монтаж должен
производиться с соблюдением всех
действующих правил и инструкций
по установке электрооборудования.
Установка датчика
Датчик температуры пола: размещается в
изоляционной трубке, которая укладывается
в основание пола (см. Рис.4) в соответствии
с нормами EN 61386-1. Окончание трубки
герметизируется и располагается как можно
ближе к поверхности пола. Трубка с
датчиком располагается посередине между
витками нагревательного кабеля. Кабель
датчика может быть удлинен до 100 м при
помощи отдельного установочного кабеля.
Если удлинительный кабель легче, чем
HO5VV-F, то он должен быть установлен
в прочную изоляционную трубку между
кабелем датчика и удлинительным
кабелем. Нельзя для этой цели использовать
две жилы многожильного кабеля,
использующегося для питания
нагревательного кабеля. Броски
напряжения, возникающие при включении,
могут повлиять на нормальную работу
прибора.
Если используется экранированный кабель,
то экран не заземляется, а подключается к
клемме 7. Двухжильный кабель размещается
в отдельной трубке.
ìÒÚ‡ÌÓÍ ÚÂÏÓÒÚ‡Ú ÒÓ ÒÚÓÂÌÌ˚Ï
‡Ú˜ËÍÓÏÚÂÏÔÂ‡ÚÛ˚(ËÒ. 4)
чژËÍ ÚÂÏÔÂ‡ÚÛ˚ ‚ÓÁ‰Ûı‡ ËÒÔÓθÁÛÂÚÒfl
‰Îfl ÔÓ‰‰ÂʇÌËfl ÍÓÏÙÓÚÌÓÈ ÚÂÏÔÂ‡ÚÛ˚
‚ÓÁ‰Ûı‡ ÔÓÏ¢ÂÌËË. íÂÏÓÒÚ‡Ú ÒÓ
‚ÒÚÓÂÌÌ˚Ï ‰‡Ú˜ËÍÓÏ ÚÂÏÔÂ‡ÚÛ˚
2 © 2010 OJ Electronics A/S
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arnold Rak OCC2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arnold Rak OCC2 in the language / languages: English, German, Dutch, Danish, French, Polish, Swedish, Spanish, Spanish as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arnold Rak OCC2

Arnold Rak OCC2 User Manual - English, German, Polish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info