702288
1
Zoom out
Zoom in
Previous page
1/20
Next page
© 2003 GE Interlogix B.V. 1047430
All Rights Reserved 12/2003
1
2
3
4
5
6
7
8
9
10
NC OC
Gouvars, Frederique (IndSys, GE Interlogix)
GSM Module
WHAT DOES IT DO?
The ATS7300 enables alarm reporting via GSM. All reporting
formats available through PSTN are fully functional, including voice
reporting or audio listen-in.The GSM module can be used for
primary reporting as well as back-up reporting (using multiple
central stations).
The ATS7300 has a provision to establish a reliable connection for
remote up-/downloading to and from the ATS panel. In data mode
the GSM module even can establish a connection up to 4800 baud
(for more details and programming options see ATS2000 / 3000 /
4000 Programming manual). A general fault indicator is available
(OC) to indicate if the battery is present, the battery fuse is ok and
the GSM network is detected.
IMPORTANT:
Disable PIN code request on your SIM card (via
any mobile telephone)
For proper operation a GSM card with subscription
is mandatory (NOT pre-paid).
The ATS7300 will only operate (dial/answer) when
connected to the home network.
A GSM module during operation can require a
maximum of 2A peak current; the back-up battery
normally wired to the control panel is now also
wired to the GSM module. The GSM module
checks the battery operation and disconnects the
battery when the battery voltage drops below 9
volts to preserve the battery (deep discharge
protection)
Make sure the antenna itself is placed outside the
control panel.
To do up/download via the GSM module, use a SIM
card that has fax and data enabled.
MOUNTING LOCATION
The ATS7300 must be mounted inside an ATS panel housing.
Important:
1. Disconnect the mains power before opening the cabinet.
Disconnect AC mains plug from AC mains wall socket.
OR
Disconnect the mains with a dedicated circuit breaker.
2. Disconnect the battery (when applicable).
MOUNTING THE UNIT
Mounting the ATS7300 into the control panel (ATS4000, Ref.
to figure ).
1. Remove the screws and lift off the control panel PCB.
2. Place the extension pillars with the plastic rings on top of the
existing pillars .
3. Place the clips in the square holes .
4. Mount the ATS7300 using the screws and extension pillars .
5. Place the ATS control panel PCB back into its original position.
Mounting the ATS7300 into the control panel
(ATS2000/3000/4500, Ref. to figure )
1. Place the clips in the square holes (use metal pillars when
available).
2. Mount the ATS7300 using screws.
Connecting the GSM module
Disconnect AC mains plug from AC mains wall socket
1. Remove the battery wires that run from the battery to the
control panel.
2. Add the blue “tap connectors” to the red and blue (or black)
battery leads.
3. Connect the additional wires, which will be clamped to the
GSM module.
4. Before clamping ensure that the battery leads will reach the
GMS module as well as the battery.
5. Connect the red wire to BATT IN + and the battery.
6. Connect the blue (or black) wire to BATT IN – and the battery.
ATS7300
GSM Module
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech ATS7300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS7300 in the language / languages: English, Dutch, Danish, French, Italian, Polish, Spanish, Norwegian as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info