702275
1
Zoom out
Zoom in
Previous page
1/8
Next page
© 2003 GE Interlogix B.V.. MAINST-ATS1202
All rights reserved 12/2003
8-Zone expansion module
CONNECTIONS: HEADERS AND SOCKETS
J2 Connection from previous 8-zone expander, DGP or
ATS control panel.
J3 Connection to next 8-zone expansion.
Connection to DGP and other 8-zone expansion cards
via 10-way cable supplied with the expander card.
The DGP or ATS control panel MUST be powered down while
an expander is being connected.
CONNECTIONS: ALARM ZONES
J1 Connector for 8 zones with common connection.
e Normally closed tamper contact
f Normally closed alarm contact
DIP SWITCHES c
Zone numbers to use Switch1 Switch2 Switch3 Switch4
9 – 16 (1
st
module) ON OFF OFF OFF
17 – 24 (2
nd
module) OFF ON OFF OFF
25 – 32 (3
rd
module) OFF OFF ON OFF
Warning: - On a control panel with 16 standard zones, the
first ATS1202 needs to be set for zones 17 - 24.
- Only consecutive zone numbers can be used.
Caution!
If a DGP or the control panel already has ATS1202
expander modules fitted through which the number of zones
exceeds 16 while the next DGP number is already being used,
then no more expanders can be fitted to the DGP or control panel.
e.g. If DGP 1 has an expander module (total 16 zones) and
DGP 2 is already in the system and programmed to be polled, then
DGP 1 cannot have any more expanders fitted.
LINKS
GND d Must remain fitted.
ZONE NUMBERING
A standard 8 zone DGP can have eight zones connected to it.This
can be expanded in increments of 8, up to 32, using the ATS1202
8-Zone expanders (A DGP can have 8, 16, 24 or 32 zones)
A control panel can have 8 or 16 zones connected to it (depending
on control panel type). This can be incremented to a maximum of
32 zones by fitting ATS1202 expander modules.
There are sixteen zones allocated to every DGP address.
If a DGP has 24 or 32 zones (two or three expanders fitted), the
additional system zone numbers are taken from the following DGP
address. If this is done, the next DGP address ceases to exist and
is not included to be polled.
e.g. DGP 1 has 24 zones (zones 17 to 40). The next DGP in
the system must now be addressed and polled as DGP 3, because
zones 33 to 40 on DGP 1 have been taken from DGP 2.
The unused zone numbers in the system (zones 41 to
48) must be programmed in the zone database as Type 0 (zone
disabled).
Control panel 1–16 DGP8 129-144
DGP1 17-32 DGP9 145-160
DGP2 33-48 DGP10 161-176
DGP3 49-64 DGP11 177-192
DGP4 65-80 DGP12 193-208
DGP5 81-96 DGP13 209-224
DGP6 97-112 DGP14 225-240
DGP7 113-128 DGP15 241-256
Module d’extension 8 zones
CONNEXIONS : ARRIVEE-DEPART
J2 Connexion provenant de la carte d’extension à 8 zones
précédente, centrale ATS ou DGP.
J3 Connexion vers la carte d’extension à 8 zones suivante.
Connexion vers le DGP et autres cartes d’extension à 8
zones via le câble à 10 fils fourni avec la carte d’extension.
Le DGP ou la centrale ATS DOIVENT être hors tension lors de
la connexion d’une carte d’extension.
CONNEXIONS DES ZONES DALARME
J1 Bornier de raccordement des 8 zones avec 0 v
commun.
Contact d’autoprotection normalement fermé.
Pos.1 Pos.2
8
C
7
6
C
5
4
C
3
2
C
1
J1
J3
J2
8
C
7
6
C
5
4
C
3
2
C
1
J1
J3
J2
8
C
7
6
C
5
4
C
3
2
C
1
J1
J3
J2
4k7
4k7
To DGP
8
C
7
6
C
5
4
C
3
2
C
1
J1
J3
J2
8
C
7
6
C
5
4
C
3
2
C
1
J1
J3
J2
8
C
7
6
C
5
4
C
3
2
C
1
J1
J3
J2
4k7
4k7
To DGP
4
3
2
1
4
3
2
1
4
3
2
1
8
C
7
6
C
5
4
C
3
2
C
1
J1
J3
J2
8
C
7
6
C
5
4
C
3
2
C
1
J1
J3
J2
4k7
4k7
To AT S
Control Panel
4
3
2
1
4
3
2
1
c
c
c
c
c
d
d
d
d
d
e
f
e
f
ATS1202
8-Zone expansion module
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech ATS1202 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS1202 in the language / languages: English, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info