702270
3
Zoom out
Zoom in
Previous page
1/12
Next page
3
LED’S (ZIE FIGUUR A)
Rx De LED knippert om aan te geven dat er pollgegevens
ontvangen worden op de systeemdatabus van het ATS
-controlepaneel. Als de LED niet knippert, dan is het
controlepaneel niet in bedrijf of de databus is defect
(meestal een bedradingsfout).
Tx De LED knippert om aan te geven dat het
gebruikersinterface (GI) reageert op het pollen van het
ATS -controlepaneel. Als de Rx-LED wel knippert maar
de Tx-LED niet, dan is het gebruikersinterface (GI) niet
geprogrammeerd voor pollen door het controlepaneel, of
het is onjuist geadresseerd.
AANSLUITINGEN VAN KAARTLEZERS (ALLEEN ATS1105) (A,
J2)
+5 V voeding en data-aansluitingen voor ATS magnetische
kaartlezers (alleen ATS1105).
1 D1/D lees datapuls / Wiegand D1-lijn
2 D0/D lees klokpuls / Wiegand D0-lijn
3 GND (0 V)
4 +5 V
5 +12 V
Bijkomende functionaliteit
- Aanpassen LCD contrast – Druk op de Menu * toets met
Ç of È
- Aanpassen zoemer volume, Druk op de Clear toets met
Ç (omhoog) of È (omlaag)
GI DIPSWITCHES: INSTELLINGEN (FIGUUR A)
SW1 dipswitches
Deze worden gebruikt voor het instellen van het GI-adres. Zie
figuur B voor de instelwaarden.
SW2 “A, B, C, Term”
Deze worden gebruikt om de databus af te sluiten en diverse
andere hieronder beschreven functies te activeren.
SW2-1, A Gebied 9-16
OFF De 8-gebieden-LED’s geven de status weer van de
gebieden 1–8.
ON De 8-gebieden-LED’s geven de status weer van de
gebieden 9–16.
SW2-2, B Bediendeel verlichting
OFF De verlichting van het bediendeel gaat na enige tijd uit.
ON De verlichting van het bediendeel blijft altijd aan.
SW2-3, C Magnetisch kaartformaat (alleen ATS1105).
OFF ATS-formaat
ON Niet-ATS-formaten
(bijv.: credit cards, andere kaarten met data op spoor 2).
SW2-4, TERM
OFF Niet het laatste apparaat op de databus.
ON Sluit de databus af indien dit GI het laatste is op de
databus. Zie ook de installatiehandleiding van het ATS-
controlepaneel.
COMMS AANSLUITINGEN (FIGUUR A, AANSLUITPUNT J3)
Voedingsspanning. Als de afstand tussen het
gebruikersinterface en het controlepaneel hoogstens
100 meter is, kunnen de gebruikersinterfaces gevoed
worden via de Comms + en - van het controlepaneel.
Gebruik anders de AUX PWR van de DI’s of een
hulpvoeding.
D+ Positieve en negatieve signaalaansluitingen van de
databus.
D - Remote units kunnen maximaal 1,5 km van
het ATS- controlepaneel verwijderd zijn.
IN Een Uitgangsknop (de normale stand is open, tijdelijke
drukknopschakelaar) kan aangesloten worden over “IN
en “-“. Wanneer deze knop is ingedrukt, wordt hiermee
de uitgangsfunctie aangestuurd.
UIT Open collector output, maximaal 50 mA. Het is de
eerste output van de output-controlegroep die toegekend
is aan dit gebruikersinterface.
Tastiere Remote a LCD 8 aree
INSTALLAZIONE DELLUNITÀ
Verificare che la tastiera sia montata su una superficie piatta per
evitare un cattivo funzionamento del contatto antisabotaggio.
Fissare la base del contenitore della tastiera con viti e tasselli
appropriati. Quando è richiesto il tamper antirimozione, utilizzare
una vite e tassello per fissare a muro la base della tastiera nel
punto indicato in figura A.
Per la conformità alle norme CEI 79-2 2^ ed. per il secondo II°
e III° livello, l’utilizzo del tamper antirimozione è obbligatorio.
Fissare il circuito stampato al fondo della tastiera utilizzando la vite
fornita. Fissare il coperchio della tastiera con la vite fornita.
COLLEGAMENTO DELLA TASTIERA A UNA CENTRALE (FIGURA
A)
Per le istruzioni, fare riferimento alla guida di installazione della
centrale e a quanto riportato più avanti in questo manuale.
IMPOSTAZIONE DEI DIPSWITCH DELLA TASTIERA: (FIGURA A)
Dipswitch SW1
Vengono utilizzati per identificare l’indirizzo della RAS
(Remote Arming Station, Stazione Inserimento Remoto).
Per l’impostazione, fare riferimento alla figura B.
SW2 “A, B, C, Term”
Vengono utilizzati per abilitare la resistenza terminale per il bus
dati e abilitare diverse altre funzioni, come descritto di seguito:
SW2-1, A Area 9-16
OFF I LED delle 8 aree mostrano lo stato delle aree da 1 a 8.
ON I LED delle 8 aree mostrano lo stato delle aree da 9 a
16.
SW2-2, B Retroilluminazione tastiera
OFF La retroilluminazione della tastiera è temporizzata.
ON La retroilluminazione della tastiera rimane sempre attiva.
SW2-3, C Formato tessera magnetica (Solo ATS1105)
OFF Formato Aritech.
ON Formati non Aritech
(ad es., carte di credito, qualsiasi carta contenente dati
sulla traccia 2).
SW2-4, TERM
OFF Se questo non è l’ultimo apparato sul bus dati.
ON Per terminare il bus dati se questo è l’ultimo apparato sul
bus dati. Vedi anche la guida di installazione della
centrale ATS.
LED (VEDI FIGURA A)
Rx Il LED lampeggia per indicare che il bus dati del sistema
riceve i dati di interrogazione dalla centrale ATS. Se il
LED non lampeggia, la centrale non è in funzione o il
bus dati è guasto (solitamente per un problema di cavi).
Tx Il LED lampeggia per indicare che la stazione di
inserimento (RAS) risponde all’interrogazione della
centrale ATS. Se il LED Rx lampeggia ma il LED Tx non
lampeggia, la stazione di inserimento (RAS) non è stata
programmata per essere interrogata dalla centrale
oppure è stata indirizzata in modo non corretto.
INDICAZIONI LED SU TASTIERA
Area I LED rossi numerati 1-8 (oppure 9-16) si attivano in
modo fisso quando le aree relative sono inserite. In caso
di allarme, lampeggiano lentamente (con aree
disinserite) o lampeggiano velocemente (con aree
inserite).
230 Vca Il LED verde è acceso fisso se è disponibile
l’alimentazione di rete a 230 Vca.
Allarme Il LED rosso si accende fisso, in caso di qualsiasi
allarme in un’area assegnata alla tastiera.
Guasto Il LED giallo si accende in caso di guasti al sistema.
+12
0V
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech ATS1100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS1100 in the language / languages: English, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info