47709
12
Zoom out
Zoom in
Previous page
1/12
Next page
23
GB
m odel
LB 6 T - LB 6 TX
dimensions
width cm 59,8
height cm 82
depth cm 53,7
capacity
1 - 5 Kg
electrical
connections
voltage 220/230 Volt 50 Hz
maximum absorbed power 2300 W
water
connections
maximum pressure 1 M Pa (10 bar)
minimum pressure 0,05 MPa (0,5 bar)
drum capacity 42 litres
spinning speed
up to 600 rpm
This appliance conforms with the follow ing E.E.C.
directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and
subsequent modifications
- 89/336/EEC of 03/05/89 (Electrom agnetic
Compatibility) and subsequent modifications
Using the Drilling Template
·
Place the top edge of the drilling template so that it is flush
with the top edge of the panel, making sure that it is positioned
correctly and centered in the horizontal direction (use the dotted
lines on the edges to line the template up). Mark the points on
the panel for the four holes.
· Use an appropriately sized router to mill the holes for the
two hinges, the rubber plug and the magnet.
Mounding the Parts onto the Wooden Panel
(Door)
· Insert the hinges into the holes (the movable part of the
hinge must be positioned facing away from the panel) and
fasten them with the 4 type A screws.
· Insert the magnet into the top hole on the opposite side
of the hinges and fasten it with the two type B screws.
· Insert the rubber plug into the bottom hole.
The panel is now ready to be mounted onto the machine.
Mounting the Panel into the machine
Insert the nib of the hinge (indicated by the arrow in fig. 9)
into the hole for the hinge and push the panel towards the
front of the machine. Fasten the two hinges with the type
D screws.
Inserting the machine into the Cabinet
· Push the machine into the opening, aligning it with the
cabinets (fig. 14).
· Regulate the adjustable feet to raise the machine to the
appropriate height.
· To adjust the position of the wooden panel in both the
vertical and horizontal directions, use the C and D screws,
as shown in fig. 15.
· If the machine is installed at the end of a set of modular
cabinets, mount either one or both of the guides for the
base molding (as shown in fig. 16) with the type F screws.
Adjust them for depth based on the position of the base
molding, and, if necessary, fasten the base to the guides.
Technical characteristics
90 mm
570
min
820
537
598
820
÷ 870
600 min
D
C
C
Fig. 16
Fig. 14 Fig. 15
Control programs in compliance with IEC regulation 456:
Cotton program:
Turn knob A to the "program 2"setting;
Turn knob B to the "60°C" setting.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston LB6TX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston LB6TX in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info