47703
10
Zoom out
Zoom in
Previous page
1/14
Next page
9
GB
Removing limescale
Water contains increasing amounts of limescale because of
pollution. If you live in a hard water area in addition to
using water-softener in each wash, it is a good idea to put
the machine through a cycle without laundry or detergent,
just using limescale remover.
Fig. 1
Fig. 2
Z
Trouble shooting
washer-dryers which have one, is on the O setting; the
program knob A is on the setting; the dryer knob C is on
the O setting.
Lots of vibration during the spin
Make sure:
the internal oscillating unit was released correctly at the time
of installation (see installation instructions); the washer is
levelled correctly or too tightly fitted between furniture units
and the wall.
Your washer is leaking.
Make sure:
the ring nut of the supply pipe is firmly tightened; the
detergent dispenser is not plugged and the drainage pipe is
firmly fixed.
Excessive formation of suds.
Make sure:
the type of detergent you have used - is it suitable for an
automati washer - have you used too much detergent?
The washer-dryer is not drying efficiently.
Make sure:
the end of the drain hose is not immersed in water; the
drain pump is not blocked (see "General maintenance");
the advice on maximum loads and drying times have been
followed; the drying time selected is at least 20 minutes; the
water tap is turned on.
If despite all this your washer-dryer is still not running properly,
call your local Authorized Service Centre providing the
following information:
- fault
- model code (Mod. ....)
and serial number (S/N ....)
indicated on the plate located on the bottom part of
the machine.
Never use the services of an unauthorised servicing technician
and insist on the use of original spare parts.
If the machine does not seem to be working properly before
calling the service engineer there are a number of things
you can check. Perhaps you have forgotten to push in a
button or you are not using the machine properly.
Machine won't start
Make sure:
the appliance is plugged to the mains socket; you have
electricity in your home, the door is firmly shut, the ON/OFF
button I is on I, the programming cycle knob, in washer-
dryers which have one, is on O, the programme is properly
set and the mains water tap is open.
Machine won't fill
Make sure:
the water tap is open and connected correctly to the hose;
the water mains has not been cut off and that water pressure
is sufficient; also check the hose for kinks.
Water is pumping in and out all the time
Make sure:
there are no kinks in the drain pipe and that it is at least at a
height greater than 60 cm; the pipe mouth is not below
water level and that the wall drain has no air outlet. If the
problems continue even after you have checked these points,
shut the water tap and turn off your machine.
Problems with pumping out water or spinning
Make sure:
the programme selected has a draining cycle; the non
creasing "hydropstop" button, on washer-dryers which have
one, has not been pressed accidentally; the drainage pump
is not jammed; the drain pipe is bent; the drainage piping is
plugged; any drainage pipe extensions are properly
connected and do not prevent water flow.
The washer-dryer is not drying
Make sure:
the plug is inserted properly into the socket; there is electricity
in the house; the washer-dryer door is closed; the ON-OFF
button I is on the I setting; the programming cycle knob, in
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston CD12T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston CD12T in the language / languages: English as an attachment in your email.

The manual is 1,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info