609131
5
Zoom out
Zoom in
Previous page
1/18
Next page
5
NA
Standpipe Drain System - Installations require a minimum
1 ¼” (3.2 cm) diameter standpipe with a minimum carry
away capacity of 7 gallons (26 liters) per minute.
Wall or Floor Standpipe Drain System - The top of the
standpipe must be between 25” (62 cm) - 34” (86 cm)
from the bottom of the washer (Fig. 4).
Sink Drainpipe System
-
Entry into the sink drain
system must be above the trap (Fig. 5). When routing the
drain hose through cabinets or walls, use a protective ma-
terial such as electrical or duct tape to cover sharp edges
that could damage the drain hose. Use a suitable clamp
to secure the drain hose to the “Y” branch or the disposer.
With a sink drainpipe system, you may connect directly:
1) to a disposer by following the manufacturers attachment
method.
2) directly to a “Y” branch tail piece (available at most
hardware stores).
3) Through the floor to a separate trap. The trap must be
vented to prevent siphoning. To provide proper venting,
install an Air Gap Kit (available at most hardware stores).
4) To the to the faucet using a Faucet Adapter Kit (available
separately).
• Use a U-Clamp (provided in your accessories packet)
or suitable item to secure the outlet end of the drain hose
(pre-installed on the back of your machine).
25" (62 cm) min.
with an air break
Laundry Sink Drain
Fig. 5
Sink Drain W/ "Y" Branch Tailpiece
Important:
Make sure that the drain hose is
not kinked and that water flow is not restricted.
!
H
C
Connecting Water Inlet
If the water pipes you will be connecting to are new or
unused, run the water until clear to remove any debris that
could clog the water valve screens or valves before con-
necting the machine. NOTE: Supply shut-off valves should
be easily accessible.
1. Screw the cold water fill
hose (C blue connector) onto
the cold water supply until
tight.
2. turn on the cold water
supply and check for leaks,
tighten if necessary.
3. Screw the hot water fill
hose (H red connector) onto
the hot water supply until tight.
4. Turn on the hot water supply and check for leaks,
tighten if necessary.
Drainage
Standpipe Diameter/Capacity - Needs a 1 ¼”
minimum diameter standpipe with a minimum carry-away
capacity of 7 gallons per minute.
Top of Standpipe - Must be between 25” - 34” high
from the bottom of the machine.
Outlet End of Drain Hose (provided with the unit)
- Must be at least 20” above the bottom of the washer-
dryer. An air break must be available at the standpipe to
avoid siphoning. No more than 6” of the drain hose should
be inserted into the drain pipe to prevent siphoning.
Connecting the drain hose
It is possible for the water to be discharged into a sink,
standpipe or drainpipe, but an air break must be available
at a min. 20” height to prevent the machine from siphoning
(Fig. 6).
Important:
Water pressure MUST range wi-
thin the values indicated on the “Technical Data”
chart.
!
!
Important:
Do not use excessive force. Da-
mage to the couplings can result. The couplings
should be tightened by hand; a tool should only
be used if a leak occurs.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston ARWXF 129 W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston ARWXF 129 W in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info