642231

Argon TT1v2 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page


www.argonaudio.com 2
TT1
v
2
Connection to the amplifier
The external phono leads must be connected to your
amplifier.
Connections : Red right channel / Black left channel. If
your amplifier does not have an integrated phono stage
you will need to require an external phone stage. Ask at
your local hi-fi dealer..
Plug and play - Quick set up (factory fitted cartridge
only)
Your turntable has been designed to be very simple to
set-up and use. We have designed this turntable so that
correct tracking weight can be achieved by simply
pushing the balance weight as close to the stop point
as possible. Fig 2. This will automatically set the arm to
within the recommended tracking range for the factory
fitted stylus (1.5g - 2.0g). The Bias slider should be set
to the same figure as the tracking weight. Fig 3.
Advanced Set-up (when using a different model of
cartridge)
If you choose to change the factory fitted cartridge a
tracking pressure gauge is required to correctly apply
the required down force. Any Hi-Fi dealer should be
happy to help with this setup procedure when you
purchase a new cartridge. Always use a down force
which corresponds to the upper limit of the cartridge
maker's recommended range. A new cartridge must be
aligned correctly as shown in fig 4. Adjust the cartridge
position in the head-shell so that the stylus tip is
vertically aligned with the front of the hole marked A.
Ensure the cartridge is sitting square in the head-shell
before fully tightening.(Take care not to over tighten.
Set the bias adjustment slider fig 3. to the same number
as the tracking force. For example 1.5g tracking force =
1.5 on the bias slider.
Hints & Tips
Mount the turntable on a rigid, level surface. Avoid
mounting on hollow or heavy cabinets or anything
mounted on a flexible wooden floor. The Argon
turntable support is the ideal solution.
Keeping the lid closed while playing records will prevent
dust falling on to the record surface and should make
cleaning unnecessary. Depending on the room
environment and ambient temperature, playing with the
lid open may offer sonic improvements. You can
experiment to optimise the performance best suited to
your room.
Do not use any record cleaner that works while the
record is playing or any cleaners that use water or
solvents. If you keep your records stored in their
sleeves, avoid touching the playing surfaces and keep
all water and fluids away, cleaning should not be
necessary. Do not worry about visible dust on the
record surface, this is brushed aside by the stylus and
any that collects on the stylus can be easily blown
away. In general, record cleaning is overdone and one
should not believe all the claims made by record
cleaner manufacturers.
Leave the turntable running during a record playing
session. Switch on before the session and only switch
off after you have finished. This will increase the life of
the motor and drive belt.
Do not lift the centre hub out from the main bearing.
The bearing is factory assembled with a film of special
thick lubricant. If the centre hub is removed this film
may be disturbed and the accuracy of the turntable
could be affected.
The arm earth (or ground) is automatically connected
through the arm cable screening. No other earthing
should be necessary.
Save the original packing in case you ever need to
transport the turntable.
Do not use any polish on the turntable or lid. To clean,
wipe gently with a soft cotton duster (slightly damp only
if required).
Argon turntables are designed to optimise performance
for music reproduction and therefore no compromises
have been made to give quick start times. The normal
time taken for full speed to be reached is between 2
and 5 seconds.
Warning: Any attempt to repair or modify this turntable
by persons other than authorized personnel may
invalidate the guarantee. Should you experience any
problem with your turntable please contact your dealer.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argon TT1v2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argon TT1v2 in the language / languages: English as an attachment in your email.

The manual is 0,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info