160621
12
Zoom out
Zoom in
Previous page
1/14
Next page
E12
E13
English
Setting the clock and alarm
When Solo is in stand-by, press MENU to set the clock or alarms.
Use the left and right buttons on the remote control to select the item to change, then use the up and
down buttons to change the value. For example, after pressing MENU to enter the clock/alarm setting
menu, pressing up and down will change between setting the clock and setting one of the alarms.
Solo allows up to four different alarms to be set.
Stopping or pausing an alarm
To stop an alarm ringing, press the power button on the front-panel or remote control. Alternatively, press
OK to enter ‘snooze’ mode; the alarm will re-sound after a 10-minute delay. To cancel snooze-mode, press
the power button.
Stand-by state
Earlier
Later
Off
On
Alarms go off at the scheduled
time for highlighted days. In this
example, alarms are set to go off
on weekdays only.
Select a
signal source
Set AM
or PM
Set minutes
for alarm
Set hours
for alarm
Set alarm
on or off
Set the
day
Set the time
(minutes)
Set the time
(hours)
Confirm
settings
OK
Set 12/24
hour clock
Stand-by state
Exit to
time-of-day
display
Earlier
Later
AM
PM
Off
On
12HR
24HR
Earlier
Later
Earlier
Later
Previous
Next
Exit to
time-of-day
display
Select an alarm
or set the clock
Set alarm days
on or off
Setting the clock
Setting alarms
Previous item Next item
Previous item Next item
DAB Setup
This menu item is shown only when the selected source is DAB.
There are two options under this menu item – ‘Scan’ and ‘Erase settings’. Selecting ‘Scan’ causes Solo
to search for new DAB stations. If any are found, then they will be added automatically to the list of
available stations.
Scanning for new stations does not erase old stations that are no longer transmitted – over time, or if
you change location, this may lead to you having a number of stations in your list that cannot actually be
received. In this case, select ‘Erase settings’, then perform a new scan; when the scan is complete, only
stations that are available currently in your area will be shown.
Set Preset
This menu item is shown only when the selected source is DAB, FM or AM.
See the section ‘Programming station presets’ on page 7 for more information.
Adjusting Zone 2 volume
Press and hold MENU on the front panel until ‘Z2 Vol’ is displayed, then use the volume control to
decrease/increase the Zone 2 volume. Press MENU again to exit.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam solo music at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam solo music in the language / languages: English as an attachment in your email.

The manual is 1,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam solo music

Arcam solo music User Manual - English, German, Dutch, French, Portuguese - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info