578760
4
Zoom out
Zoom in
Previous page
1/14
Next page
A85/P85
4
Installation: A85 integrated ampli er
Positioning the unit
Place your ampli er on a level, rm surface.
Avoid placing the unit in direct sunlight or near sources of heat
or damp.
Ensure adequate ventilation. Do not place the unit in an
enclosed space such as a bookcase or cabinet as both of
these will impede air ow through the ventilation slots.
Connecting to loudspeakers
You can connect one or two pairs of loudspeakers to your
ampli er, provided each pair is rated between 816. If one or
both pairs have an impedance of less than 8, the combined
load on the ampli er falls below 4 and could cause an
overload. If so, the overload protection circuit engages and the
ampli er will not work.
To connect one pair of loudspeakers, use the
SP1 terminals.
SP1 and SP2 terminals
4
Both sets of loudspeaker terminals can be switched off by
pressing the MUTE button on the remote control. To switch SP1
and SP2 independently, use the front panel switch
7
(see
page 6) or the remote control (see page 9).
Your ampli er is tted with loudspeaker terminals to BFA
(British Federation of Audio) standard speci cation.
BFA loudspeaker terminals
The terminal will accept spade terminals, bare wires or a
BFA plug. BFA plugs are available from your Arcam dealer. To
connect a bare wire or spade terminal, unscrew the red (or
black) part of the loudspeaker terminal rst.
Insert the wire or spade terminal and screw it back up.
CAUTION: Do not over tighten the loudspeaker terminals or
use a wrench, pliers, etc., as this could cause damage to the
terminals which will not be covered under warranty.
Connect the right speaker to the terminals on the back of
your ampli er marked
R and the left speaker to the terminals
marked L.
Connect your loudspeakers so that the red (positive/+) terminal
on each loudspeaker is connected to the red (positive/+)
terminal on the ampli er. Your loudspeaker cables may be
marked to show polarity (negative/ and positive/+), if not, then
the positive terminal can usually be identi ed by a ridge or
coloured marking.
Now connect your loudspeakers black (negative/) terminals to
the black (negative/) terminals on the ampli er.
Ensure that no stray strands of inner wires are allowed to touch
another cable or the ampli ers casing. This can cause a short
circuit and damage your ampli er!
Wiring your loudspeakers
LR
+
PHONO
+
SP1
SP2
POWER INLET
PRE OUTPWR IN
6 8 9 bk bl bm bn bo bp54 bq1
4 16 OHMS
L
R
L
R
L
R
VOLTAGE
SELECT
230V
RECORD
OUT
PLAY
IN
TAPE 1
RECORD
OUT
PLAY
IN
VCR/TAPE 2 DVD AV TUNER CD AUX
INTEGRATED
PRE/PWR
MM
MC
32
REMOTE
IN
TRIG
OUT
7br
Arcam A85 amplifier
R
L
+ +
Right
speaker
+
+
Left
speaker
A85/P85 multi.id 03/29/01, 3:34 PM4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam DiVA P85 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam DiVA P85 in the language / languages: English, German, French as an attachment in your email.

The manual is 0,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info