635920

Andrews Zephyr ET Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
Operation Instructions
The control panel on the room unit is illustrated below
Revolve thermostat knob fully CLOCKWISE to the number ‘8’ position
Plug in the room unit mains cable, and switch on the electricity, red
mains light will illuminate.
Select ‘Fan Only’ with the mode switch. The fan will start.
Select ‘Fan Speed’ with the fan speed switch, high or low
depending on air velocity required.
Select ‘Cooling’ with the mode switch, and revolve the thermostat
knob fully ANTI-CLOCKWISE to he number ‘1’ position. After a
delay of 10 mins the green ‘Cooling’ light will illuminate and the
machine will proceed to cool the air.
Monitor the room temperature and when it has reduced to the desired
level, very slowly revolve the thermostat knob back, clockwise until the
green ‘Cooling’ light goes out. The room unit will now control the room
temperature cooling automatically at this setting.
Routine Maintenance
The air filter must be kept clean, never allow to become choked with
dust or dirt. If allowed to do so, the performance of the unit will become
impaired, resulting in loss of air flow, freezing up the evaporator coil and
possible component damage.
Accessing the Filter
On machines fitted with a hinged lower panel, open panel. The filter is
located on front of the evaporator. A second filter is fitted to the rear panel
on all air cooled machines.
On machines without a hinged front panel, to access the filter, lift out the
return air grille on the front face of the unit. On refitting the filter ensure that
it is correctly positioned covering the whole face of the grille.
The filter (see Fig 4) can be washed in warm, soapy water, rinsed and
shaken dry before replacement. Frequency of cleaning depends upon
Operating Instructions - Zephyr ET
Click www.andrews-sykes.com or Call Us Free 0800 211 611
application and can only be determined by the user. However, you should
never allow more than two months to elapse between cleaning. The
probable life of the filter will be about one year and spares are available
from the supplier of the unit itself. Failure to have filter fitted during
operation will cause serious damage (see fig. 4 / 5).
Problem Likely Cause Solution
No cooling Amber ‘ATTENTION’
light illuminated. High
level condensate trip.
Condensate pump not reducing water level.
Kink in condensate tube between room
unit and external heat exchanger? Leak
inside room unit. Pump filter inside room unit
blocked. Condensate tube frozen.
No cooling Amber ‘ATTENTION’
light illuminated. Bottle
fitted switch trip.
On machines without a removable
bottle, ensure link fitted to terminal
block. On machines with , ensure bottle
fitted correctly.
No cooling Amber ‘CONTAINER
FULL’ light illuminated.
High level condensate
trip.
On machines without a removable
bottle, as above. On machines with a
bottle, remove container and replace
correctly. To empty the condensate
bottle, pull forward the lower front panel,
(Fig 2).
The front cover will come forward, giving
access to the container, (Fig 3).
Empty the container, and carefully
replace.
Ensure the drain pipe is fitted into the
container.
The filter is located on the rear of the
unit, ensure it is kept clean.
Fitting the hot air exhaust
Fig.2
Fig.3 Fig.4
Fig.5
Fig.1
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Andrews Zephyr ET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Andrews Zephyr ET in the language / languages: English as an attachment in your email.

The manual is 0,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info