The A&D blood pressure monitor is one of the most advanced
monitors available and is designed for ease of use and accuracy.
This device will facilitate your daily blood pressure regimen.
We recommend that you read through this manual carefully before
using the device for the first time.
2.Preliminary Remarks
This device conforms to the European Directive 93/42 EEC for
Medical Products. This is made evident by the
mark of
conformity. (0123: The reference number to the involved notified
body)
The device is designed for use on adults only, not newborns or
infants.
Environment for use. The device is for use in the home healthcare
environment.
This device is designed to measure blood pressure and pulse rate
of people for diagnosis.
3.Precautions
Precision components are used in the construction of this device.
Extremes in temperature, humidity, direct sunlight, shock or dust
should be avoided.
Clean the device and cuff with a dry, soft cloth or a cloth dampened with
water and a neutral detergent. Never use alcohol, benzene, thinner or
other harsh chemicals to clean the device or cuff.
Avoid tightly folding the cuff or storing the hose tightly twisted for
long periods, as such treatment may shorten the life of the
components.
Take care to avoid accidental strangulation of babies or infants
with the hose.
Do not twist the air hose during measurement. This may cause
injury due to continuous cuff pressure.
The device and cuff are not water resistant. Prevent rain, sweat
and water from soiling the device and cuff.
Measurements may be distorted if the device is used close to
televisions, microwave ovens, X-ray or other devices with strong
electrical fields.
Wireless communication devices, such as home networking
devices, mobile phones, cordless phones and their base stations,
walkie-talkies can affect this blood pressure monitor.
Therefore, a minimum distance of 11 feet should be kept from
such devices.
When reusing the device, confirm that the device is clean.
Used equipment, parts and batteries are not treated as ordinary
household waste, and must be disposed of according to the
applicable local regulations.
Do not modify the device. It may cause accidents or damage to
the device.
To measure blood pressure, the arm must be squeezed by the
cuff hard enough to temporarily stop blood flow through the
artery. This may cause pain, numbness or a temporary red mark
to the arm. This condition will appear especially when
measurement is repeated successively. Any pain, numbness, or
red marks will disappear with time.
Measuring blood pressure too frequently may cause harm due to
blood flow interference. Check that the operation of the device
does not result in prolonged impairment of blood circulation,
when using the device repeatedly.
Clinical testing has not been conducted on pregnant women. Do
not use the device on pregnant women.
If you have had a mastectomy, please consult a doctor before
using the device.
Do not let children use the device by themselves and do not
leave the device within the reach of children.
There are small parts that may cause a choking hazard if
swallowed by mistake by infants.
Do not touch the batteries, the patient and the DC jack at the
same time. That may result in electrical shock.
Contraindications
The following are precautions for proper use of the device.
Do not apply the cuff on an arm with another medical electrical
equipment attached. The equipment may not function properly.
People who have a severe circulatory deficit in the arm must
consult a doctor before using the device, to avoid medical
problems.
Do not self-diagnose the measurement results and start
treatment by yourself. Always consult your doctor for evaluation
of the results and treatment.
Do not apply the cuff on an arm with an unhealed wound.
Do not apply the cuff on an arm receiving an intravenous drip or
blood transfusion. It may cause injury or accidents.
Do not use the device where flammable gases such as
anesthetic gases are present. It may cause an explosion.
Do not use the device in highly concentrated oxygen
environments, such as a high-pressure oxygen chamber or an
oxygen tent. It may cause a fire or explosion.
4.Parts Identification
Display
5.Symbols
Symbols that appear on the display
Symbols Function / Meaning Recommended Action
A
ppears while measurement
is in progress. It blinks when
the pulse is detected.
Measurement is in
progress. Remain as still
as possible.
I.H.B. appears when an
irregular heartbeat is detected.
It may light when a very slight
vibration like shivering or
shaking is detected.
Previous measurements
stored in memory.
FULL BATTERY
The battery power indicator
during measurement.
LOW BATTERY
The battery power is low when
it blinks.
Replace all batteries with
new ones when the mark
blinks.
A
ir Socke
t
Air Connector Plug
A
ir Hose
Proper fit range
Measurement in progres
s
Inflation complete
Inflation in progres
s
Cuff
1 to 2 cm
Artery position mark
Secure the fabric fastener
Air hose
Index
and Proper fit range
At heart level
Refer to the section
"7.1 Normal Measurement"
Press the_START_button
The desired pressure
Inflation in progress
Press and hold the
_START_button
Release the_START_
button to stop inflation
Press and hold the
_START_button
The mark blinks.
Data is cleared.
Release the
button
Select "" to
clear data.
Turns off automatically
5 seconds
Step 1
Step 3
Step 4
Step 2
Press and hold the
_START_button
Release the button
mark
Average data
Data number
Stored Data
To next data
Turns off automatically
No data
WHO Classification Indicator
Severe hypertension
Moderate hypertension
Mild hypertension
High normal
Normal
Optimal
Exhausts remaining air
automatically
At heart level
Press the_START_button
All of the display segments
Zero display
Starts inflation
Pressurizing
Measurement in progress
Systolic pressure
Diastolic pressure
WHO classification
Pulse rate
Turn off with the
_START_button
Pressurizing Releasing air
Display
Air Hose
Arm Cuff
START
Button
Index
Air Socket
Proper fit range
Artery position mark
A
ir Connector Plug
Battery Compartment
Battery Cove
r
MEMORY
Systolic Pressure
Diastolic Pressure
Pulse Rate
Heart Mark
Battery Indicator
I.H.B. symbol
(Irregular Heartbeat symbol)
Pressure Bar Indicator and
WHO Classification Indicator
Note: Model UA-611 doesn't have the DC jack for AC adapter.
The DC jack is located on the rear of the model,UA-651 only. The
AC adapter is an optional accessory.(sold separately)
Model UA-651 only
DC jack
AC adapter plug
AC adapter Plug
DC
j
ack
Model UA-651 only
Do not roll up shirtsleeve tightly
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for AnD UA-611 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of AnD UA-611 in the language / languages: English as an attachment in your email.
The manual is 0,25 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.