541763

Ampeg SVT-2 Pro Manual

8
Zoom out
Zoom in
Previous page
1/8
Next page
Ampeg reserves the right to change specifications without notice.
Ampeg is proudly Made in America
©1998 SLM Electronics • 1400 Ferguson Avenue • St. Louis, MO 63133 U.S.A.
P/N 47-509-11 • 04/98
Technical Specifications
OUTPUT POWER RATING 300 Watts RMS minimum continuous @ <3% THD into 2 or 4 ohms, 0.4VRMS input
TOTAL SYSTEM GAIN 76dB, @1kHz w/levels up, tones flat; -3dB @30Hz, 15kHz
TONE CONTROL RANGE
Bass: ±12dB @ 40Hz
Midrange: +12dB, -15dB @ Frequency selected (220, 450, 800, 1.6k or 3kHz)
Treble: ±12dB @ 4kHz
Ultra Low: +3dB @ 40Hz, -12dB @ 500Hz
Ultra High: +8dB @ 8kHz
Bright: +7dB @ 2kHz
GRAPHIC EQ RANGE ±12dB @ 40Hz, 90Hz, 180Hz, 300Hz, 500Hz, 1kHz, 2kHz, 4kHz, 10kHz
GRAPHIC EQ LEVEL +8dB, -10dB
SIGNAL TO NOISE RATIO 80dB typical
TUBE COMPLEMENT 12AX7 (5), 12AU7 (3), 6550 (6)
POWER REQUIREMENTS
Domestic: 120VAC, 60Hz, 460VA
Export: 100/115VAC 50/60Hz, 460VA
230VAC, 50/60Hz, 460VA
SIZE AND WEIGHT 19”W x 3.75”H x 15.75”D; 70 lbs
SVT-2 PRO Bass Amplifier
Troubleshooting
In the unlikely event that your SVT-2 PRO should stop working properly (or just stop working), take a few minutes to trou-
bleshoot it before you call for service. You can save yourself a lot of time and sometimes money by doing it yourself, and
often the cure for the problem is something quite simple. If you think the problem may be worn out tubes, see page 7 for
symptoms of tube failure.
If the problem isn’t
covered here, or if
the steps led you to
“Service Amp”,
then contact your
Ampeg dealer for
service information.
Also, you should
refer your amp for
servicing if it gets
dropped, has liquid
spilled into it, or
sustains damage to
its power cord.
Disconnect all external devices
except bass and speaker cabinet
No sound, bad sound?
YES
LEDs on?
YES
NO
Check AC outlet, power cord,
power switch, fuses; retry.
Check standby switch (20
second delay); retry.
Power LED green?
YES
NO
Green bias LEDs on?
YES
NO
Inst. volume & amp gain
to max – peak LED flashes?
YES
NO
Check bass cable; retry.
All controls set properly?
YES
NO
Sound OK?
YES
NO NO
YES
Go for it!
NO
Check speaker cable; retry.
Set controls; retry.
Re-bias or see page 7 for
possible faults; retry.
Bias LEDs flash
with signal?
Possible power
amp problem.
If these steps fail to solve
problem, service amp.
www.ampeg.com
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ampeg SVT-2 Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ampeg SVT-2 Pro in the language / languages: English as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info