168570
37
Zoom out
Zoom in
Previous page
1/38
Next page
35-EN
1 Antenna Receptacle
Connect to the supplied ISO antenna convertor plug.
2 Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a
cellular phone which provides ground shorting when
a call is received.
3 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
4 Dimmer Lead (Orange)
This lead may be connected to the vehicles
instrument cluster illumination lead. This will enable
the vehicles dimmer control to dim the backlighting
of the unit.
5 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicles
fuse box or another unused power source which
provides (+) 12V only when the ignition is turned on
or in the accessory position.
6 Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power
antenna, if applicable.
NOTE
This lead should be used only for controlling the
vehicle's power antenna. Do not use this lead to turn on
an amplifier or a signal processor, etc.
7 Fuse Holder (20A)
8 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the
vehicle's battery.
For the battery lead and battery connection
Use an extension battery lead (20A)(sold
separately) and connect it directly to the positive
(+) side of the vehicle's battery.
9 ISO Power Supply Connector
! Ground Lead (Black)
Connect this lead to a good chassis ground on the
vehicle. Make sure the connection is made to bare
metal and is securely fastened using the sheet metal
screw provided.
" Ai-NET Connector
Connect this to the output or input connector of other
product (CD changer, Equalizer, etc.) equipped with
Ai-NET.
# System Switch
When connecting a processor using Ai-NET, place
this switch in the EQ/DIV position. When no device
is connected, leave the switch in the NORM position.
NOTE
Be sure to turn the power off to the unit before changing
the switch position.
$ Power Supply Connector
% ISO Connector (Speaker Output)
& Left Rear (+) Speaker Output Lead (Green)
( Left Rear () Speaker Output Lead (Green/
Black)
) Left Front (+) Speaker Output Lead (White)
~ Left Front () Speaker Output Lead (White/Black)
+ Right Front () Speaker Output Lead (Grey/
Black)
, Right Front (+) Speaker Output Lead (Grey)
- Right Rear () Speaker Output Lead (Violet/
Black)
. Right Rear (+) Speaker Output Lead (Violet)
/ Remote Control Interface Connector
To remote control interface box.
: Ai-NET Cable (Included with CD Changer)
; Front Output RCA Connectors
RED is right and WHITE is left.
< Rear Output RCA Connectors
RED is right and WHITE is left.
= Subwoofer Output RCA Connectors
RED is right and WHITE is left.
>
RCA Extension Cable (Sold Separately)
To prevent external noise from entering the audio system.
Locate the unit and route the leads at least 10 cm away from the car harness.
Keep the battery power leads as far away from other leads as possible.
Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries
various noise suppressors, contact them for further information.
Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine tda 7592 r at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine tda 7592 r in the language / languages: English as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info