Manual Alpine mrd m 500 (page 5 of 24) (English, German, French, Spanish)

168467

Zoom out

Zoom in

1/24

EspañolFrançais

English

MONTAGE DES COUVERCLES D’ACHEVEMENT

• L’apparence du produit peut être améliorée en mon-

tant les couvercles d’achèvement sur l’unité centrale

après l’installation.

• Montez les couvercles d’achèvement une fois que

l’unité centrale a été installée.

1. Montage des supports

1) Utilisez les vis à métaux fournies

pour monter

les deux supports fournis

sur le côté situé à

l’opposé de la surface des bornes.

REMARQUE: Appliquer le ruban adhésif double-face

Effectuez la procédure ci-dessous si vous désirez fer-

mement fixer le couvercle ou si vous ne prévoyez pas

de retirer le couvercle après l’avoir monté.

1) Retirez le papier d’un côté du ruban adhésif dou-

ble-face fourni

2) Appliquez un morceau de ruban adhésif double-

face

sur la surface supérieure des deux sup-

ports

3) Retirez le papier de l’autre côté du ruban adhésif

double-face fourni

2. Appliquer le coussin

1) Retirez le papier du coussin fourni

2) Appliquez le coussin

à l’arrière du couvercle

d’achèvement

3. Montage des couvercles d’achèvement

1) Montez les couvercles d’achèvement

sur les

supports

Placez le support

verticalement depuis le côté

supérieur.

REMARQUE:

Pour retirer le support

, poussez-le verticale-

ment du bas vers le haut, dans le sens opposé à

celui dans lequel vous avez installé le support.

MONTAJE DE LAS CUBIERTAS DE ACABADO

• Se puede mejorar la apariencia del producto, mon-

tando las cubiertas de acabado sobre la unidad prin-

cipal después de la instalación.

• Montar las cubiertas de acabado después de instalar

la unidad principal.

1. Montaje de los soportes

1) Utilice los tornillos para metales incluidos

para

montar los dos soportes incluidos

en el lado

contrario a la superficie terminal.

NOTA: Aplicación de la cinta de doble cara

Realice el procedimiento siguiente cuando desee su-

jetar de forma segura el extremo de la cubierta o cuan-

do no planee quitar la cubierta una vez que está esté

montada.

1) Separe el papel de un lado de la cinta de doble

cara incluida

2) Aplique un pedazo de la cinta de doble cara

a la

superficie superior de los dos soportes

3) Separe el papel del otro lado de la cinta de doble

cara

2. Aplicación de la almohadilla

1) Separe el papel de la almohadilla incluida

2) Aplique la almohadilla

a la parte trasera de la

cubierta de acabado

3. Montaje de las cubiertas de acabado

1) Montar las cubiertas de acabado

a los sopor-

tes

Colocar los soportes

verticalmente desde la

parte superior.

NOTA:

Para quitar el soporte

, empuje hacia arriba ver-

ticalmente de abajo hacia arriba, en la dirección

contraria a la que el soporte fue instalado.

MOUNTING THE END COVERS

• The product’s appearance can be improved by mount-

ing the end covers on the main unit after installation.

• Mount the end covers after installing the main unit.

1. Mounting the brackets

1) Use the included machine screws

to mount the

two included brackets

onto the side opposite

the terminal surface.

NOTE: Applying the double face tape

Perform the procedure below when you want to se-

curely fasten the end cover or when you do not plan

on removing the cover once it is mounted.

1) Peel off the paper from one side of the included

double face tape

2) Apply one piece of double face tape

to the up-

per surface of the two brackets

3) Peel off the paper from the other side of the dou-

ble face tape

2. Applying the cushion

1) Peel off the paper from the included cushion

2) Apply the cushion

to the rear side of the end

cover

3. Mounting the end covers

1) Mount the end covers

to the brackets

Set the bracket

vertically from the top side.

NOTE:

To remove the bracket

, push up vertically from

the bottom upwards, in the opposite direction of

when the bracket was installed.

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpine mrd m 500 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpine mrd m 500 Manual

Product: