536969
38
Zoom out
Zoom in
Previous page
1/46
Next page
38-EN
The CD is being improperly inserted.
Make sure the CD is being inserted following instructions in the
CD Player Operation section.
Unable to fast forward or backward the CD.
The CD has been damaged.
Eject the CD and discard it; using a damaged CD in your unit can
cause damage to the mechanism.
CD playback sound skips due to vibration.
Improper mounting of the unit.
Securely re-mount the unit.
The disc is very dirty.
–Clean the disc.
The disc has scratches.
Change the disc.
The pick-up lens is dirty.
Do not use a commercially available lens cleaner disc. Consult
your nearest Alpine dealer.
CD playback sound skips without vibration.
The disc is dirty or scratched.
Clean the disc; damaged disc should be replaced.
Error displays (built-in CD player only).
Mechanical error
Press . After the error indication disappears, insert the disc
again. If the above-mentioned solution does not solve the problem,
consult your nearest Alpine dealer.
CD-R/CD-RW playback not possible.
Close session (finalisation) has not been performed.
Perform finalisation and attempt playback again.
MP3, WMA or AAC is not played back.
Writing error occurred. The MP3/WMA/AAC format is not
compatible.
Make sure the MP3/WMA/AAC has been written in a supported
format. Refer to “About MP3/WMA/AAC” on page 15, then
rewrite in the format supported by this device.
The sound is not output from the speakers.
Unit has no output signal of the internal amplifier.
POWER IC is switched to “ON”, refer to “Connecting to an
External Amplifier (POWER IC)” on page 21.
iPod does not play and no sound is output.
The iPod has not been recognised.
Reset this unit and the iPod. Refer to “Initial System Start-Up on
page 9. To reset the iPod, refer to the Owner’s Manual of the iPod.
•No CD is inserted.
–Insert a CD.
Although a disc is inserted, “NO DISC” is displayed and the unit does
not start to play or eject the disc.
Remove the disc by following these steps:
Press the button again for at least 2 seconds.
If the disc still does not eject, consult your Alpine dealer.
Mechanism error.
1 Press the button and eject the CD.
If not ejecting, consult your Alpine dealer.
2 When the error indication remains after ejecting, press the
button again.
If the error indication still does not turn off after pressing the
button for a few times, consult your Alpine dealer.
When “ERROR” is displayed:
If the disc cannot be ejected by pressing , press the RESET switch
(Refer to “Initial System Start-Up” on page 9) and press again.
If the disc still cannot be ejected, consult your Alpine dealer.
A copy-protected WMA file was played back.
You can only play back non-copy-protected files.
A sampling rate/bit rate not supported by the unit is used.
Use a sampling rate/bit rate that is supported by the unit.
Database error or decoder error.
You can solve the problem by switching the source.
Communication error or boot error, etc.
You can solve the problem by reconnecting the Flash Memory or
changing source.
Abnormal current is run to the USB Flash Memory device.
You can solve the problem by switching the source.
No song (file) is stored in the Flash Memory.
Connect the Flash Memory device after storing songs (files).
A sampling rate/bit rate not supported by the unit is used.
Use a sampling rate/bit rate that is supported by the unit.
A copy-protected WMA file was played back.
You can only play back non-copy-protected files.
MP3/WMA/AAC
Audio
iPod
Indication for CD Player
Indication for USB Memory
UNSUPPORT
or
UNSUPPORT
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine CDE-135BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine CDE-135BT in the language / languages: English as an attachment in your email.

The manual is 3,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alpine CDE-135BT

Alpine CDE-135BT User Manual - German - 53 pages

Alpine CDE-135BT User Manual - Dutch - 53 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info