541362

Allen-Heath GL 2400 Manual

13
Zoom out
Zoom in
Previous page
1/40
Next page
GL2400 User Guide 13
Audio Connections
The GL2400 uses professional grade 3 pin XLR and 1/4" TRS (3 pole) jack sockets. To
ensure best performance, we recommend that you use high quality audio cables and
connectors, and take time to check for reliable and accurate cable assembly. It is well
known that most audio system problems are due to faulty or sub standard interconnecting
leads. The following plugs may be used to connect audio to the console:
Avoid reversing + and - on balanced connections as this will result in reversed polarity (out
of phase) signals which may cause signal cancellation effects.
Where long cables runs are required, balanced interconnections should be used. However,
line level interconnections between more affordable 2-wire (signal, ground) unbalanced
equipment and the console are unlikely to cause problems if the cables are kept shorter
than 10 metres or so. Refer to the wiring diagrams on the opposite page.
Dealing with Ground Loops, Buzz and Interference
For optimum performance all audio signals should be referenced to a solid, noise-free
ground (earth) point, frequently referred to as the ‘star point’ or ‘clean earth’.
A ground loop is created when potential differences exist between grounds at different
points in the system, and the signal has more than one path to ground. In most cases
ground loops do not result in audible problems. Should you experience hum or buzz
caused by a ground loop, check first that each piece of equipment has its own separate
path to ground. If so, operate ground lift switches on connected equipment in accordance
with the instruction manuals. Alternatively disconnect the cable screen at the destination
end only. This breaks the offending loop while keeping the signal shielding down the
length of cable.
WARNING For operator safety, do not remove the ground (earth) connection
in the power lead of the console or connected equipment.
To avoid interference pickup keep audio cables away from mains power units and cables,
lighting cables, thyristor dimmer units, computer equipment and mobile phones. Where
this cannot be avoided, cross the cables at right angles to minimise interference
A note about balanced connections
A differentially balanced connection has two signal wires, signal + (hot) and signal - (cold)
and a shield. The signal source generates positive going polarity down the + wire and
negative polarity down the – wire. The destination input stage accepts the + signal on its
non-inverting (+) input pin, but it inverts the – signal, adding it to the + signal. The result is
that the wanted signal is boosted. Now examine what happens when unwanted
interference (hum and noise) is induced into the cable. The noise is induced equally and
with the same polarity into both wires. At the destination input the – wire signal gets
inverted and added to the + signal. Because the polarity is the same on both input wires
the noise cancels itself out at this input. For this interference rejection to work it is important
that the source, the cable and the destination input are all balanced. Balancing provides
greatest advantage with low level signals such as those produced by microphones.
An impedance balanced
output provides similar interference rejection, but not as much
maximum drive capability as the differentially balanced output, typically +20dBu versus
+26dBu. It does not generate a negative polarity signal at its – output. Instead, the – wire
has no signal but is held at the same impedance as the + wire. This means that both wires
pick up the noise equally resulting in the advantage of noise cancellation as described
above when connected to a balanced input stage.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath GL 2400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath GL 2400 in the language / languages: English as an attachment in your email.

The manual is 4,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info