Manual Alecto WS-2300 (page 1 of 2) (English)

627481

Zoom out

Zoom in

1/2

User’s manual

Weather station with wireless outdoor sensor

WS-2300

Overview:

Indoor unit:

1. Display:

Shows time, indoor and outdoor temperature and weather

forecast.

2. SNOOZE / LIGHT button :

Snooze button for the alarm function.

Also turns on the display lighting.

3. ALARM SET button :

For checking and setting the wake-up alarm.

4. CH/+ button:

Selection button when using multiple outdoor units and

the ‘+’ button during setup.

5. MEM/- button:

Memory button when checking min and max values and

the ‘-’ button during setup.

6. DISPLAY SET button:

Function setup button.

7. °C / °F switch:

To switch the temperature display between

degrees Celsius and degrees Fahrenheit.

8. SENSOR button:

To pair the indoor unit with the outdoor unit.

9. RCC button:

To turn the DCF receiver on or off.

10. RESET button:

To restart the indoor unit in case of a (possible) error.

11. Battery compartment.

Outdoor unit:

1. Monitor-LED: Illuminates as soon as the outdoor

unit is sending measurement data to the indoor

unit.

2. Display, shows alternately the temperature and the

humidity.

3. CH 1.2.3 switch:

To set the outdoor unit to a different channel.

4. RESET button: To restart the outdoor unit in case

of a (possible) error.

5. Suspension eye: Provision to suspend the outdoor

unit from a wall.

6. Battery compartment.

Power supply:

Indoor unit:

Slide down the battery cover at the rear of the unit

and insert 2 AA 1.5V batteries according to the mark-

ings inside the battery compartment. Slide the battery

cover back onto the indoor unit.

The indoor unit will now start a 1 minute scan to

search for the outdoor unit. Therefore, you’ll need to

insert the batteries into the outdoor unit within that

minute.

Outdoor unit:

Slide down the battery cover at the rear of the unit,

slide the CH switch to the position ‘1’ and insert 2 AA

1.5V batteries according to the markings inside the

battery compartment. Slide the battery cover back

onto the outdoor unit.

Weak battery warning:

As soon as the batteries of the outdoor unit become

exhausted, the symbol will illuminate on the

display of the indoor unit.

Now please replace the batteries of the outdoor unit.

The indoor unit does not provide a battery warning.

Replace the batteries of this unit as soon as the

display becomes dim or weak.

Pairing the indoor unit / outdoor unit:

Automatically:

As soon as you insert the batteries into the indoor

unit, the indoor unit will start a 1 minute scan to

search for the signal of the outdoor unit. Therefore,

if you insert the batteries into the outdoor unit within

that minute and the units will ‘nd’ each other, they

will be automatically paired and the display of the

indoor unit will show the temperature transmitted by

the outdoor unit.

Manually:

If the units cannot be paired automatically, or after

replacing the batteries, you can pair the outdoor unit

(again) with the indoor unit as follows:

1. use a sharp object to briey press the RESET

button on the rear of the indoor unit

2. use a sharp object to briey press the RESET

button on the rear of the outdoor unit

3. the units will nd each other (again) after several

seconds and the indoor unit will display the tem-

perature transmitted by the outdoor unit.

Clock:

Introduction

The WS-2300 is provided with a built-in DCF

receiver which receives the DCF time signal from

Frankfurt. This signal ensures that the clock shows

the time very accurately, provided a strong enough

signal is being received.

Automatically:

As soon as you insert the batteries into the indoor

unit, the clock will start searching for the DCF radio

signal for the time while the antenna symbol

is ashing. After several seconds or minutes the

WS-2300 will start showing the correct time. In

extreme cases, it can take over a day before the DCF

time is shown.

Manually:

If the clock cannot receive the radio signal or cannot

receive it well enough, you can set the clock manu-

ally as follows:

1. press and hold the DISPLAY SET button for

2 seconds, 12Hr or 24Hr will appear in the

display

2. use +/- to set the time format, then briey press

the DISPLAY SET button

3. use +/- to set the hours and then briey press the

DISPLAY SET button

4. use +/- to set the minutes and then briey press

the DISPLAY SET button

5. use +/- to set the seconds to 0 (this allows you to

have the clock run synchronously with your own

clock) and then briey press the DISPLAY SET

button

6. use +/- to set the hour difference compared to the

DCF time. E.g. for use in the Benelux select ‘0’

and then briey press the DISPLAY SET button

The clock is now set manually.

When the DCF receiver is enabled and a strong

signal is being received, the receiver will overwrite

the clock display.

Switching the DCF receiver on/off:

You can turn off the DCF receiver as follows, allow-

ing you to have only the time and date shown on the

display according to your programming:

• turn off: press and hold the RCC button at the

rear of the indoor unit for 4 seconds until the

antenna symbol disappears.

You can turn the receiver back on as follows:

• turn on: briey press the RCC button at the rear

of the indoor unit until the antenna symbol

starts ashing

‘DST’ in the display.

‘DST’ stands for Daylight Saving Time.

‘DST’ illuminates when the displayed time is the

daylight saving time.

1 2 3 4

RESETCH 1 2 3

433MHz

HYGRO-THERMO

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alecto WS-2300 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alecto WS-2300

Alecto WS-2300 User Manual - German - 2 pages

Alecto WS-2300 User Manual - Dutch - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alecto WS-2300 Manual

Product: