668915
1
Zoom out
Zoom in
Previous page
1/2
Next page
INTRODUCTION
The Alecto DVM-67 is a wireless audio/video baby monitor,
suitable for private use indoors.
You can either watch and listen continuously or you can have
the baby monitor switch on automatically as soon as your
baby starts crying.
The Alecto DVM-67 meets all essential requirements and
other provisions as described in the European Directive
1999/5/EC.
The declaration of conformity is available
on the website www.alecto.nl
Use of this equipment is allowed in all countries of the EU. In
France, Italy, Russia and Ukraine, only indoor use is allowed.
ATTENTION
Before you start using the set, please remove any protective
foil from the parent unit and baby unit.
ICONS ON THE DISPLAY
upper part of the display, during normal use
indicates the reception strength:
strong reception
good reception
average reception
bad reception
receiver is searching for a camera
no camera detected
x
(x = 1 ~ 4) shows which camera you are viewing
‘monitoring mode’ (setup choice to view cameras one after
the other when using multiple cameras)
volume set to 0 (speaker turned off)
VOX is activated (unit switches on automatically when the
baby starts crying)
temperature display of the baby room
battery indication:
battery is empty
battery is full
animation while the bat-
tery is charging
appears when the adaptor is connected and the battery is
not or incorrectly installed
icons on the display during setup
this icon is followed by the number of registered cameras
which you can select using the and buttons
in this menu, you can set the display brightness
here you can set the sensitivity level for the VOX function
in this menu, you can turn the VOX function on or off
here you can choose to have the temperature shown in
degrees Celsius or degrees Fahrenheit
in this menu, you can register additional cameras on the
receiver
INSTALLATION
BABY UNIT:
Power:
1. Connect one of the
supplied 6V power
adaptors to the 6V
DC input of the baby
unit.
2. Insert the adapter into
a 230V wall socket.
Only use the supplied power adaptor with model number
S003IV0600060.
Wall-mounting:
Drill two holes next to each other in the
wall separated by a distance of 5.4cm
and insert plugs and screws. The head
of the screw should stick out of the wall
for several millimeters.
Slide the foot of the baby unit over the
screws and then press the baby unit a
little downwards.
Tips for placement:
For use as a baby monitor:
place the baby unit at least
1-2 meters away from your
baby and make sure to safely
tuck away the adapter cable.
For optimal range, it is advis-
able to set up the baby unit
as high as possible, free from large metal surfaces.
The temperature protrudes from the rear of the baby unit.
Make sure this sensor hangs freely, unexposed to direct
sunlight and avoid heat from e.g. light bulbs.
The baby unit is not waterproof. When using outdoors,
make sure to protect the baby unit against moisture and
sand.
PARENT UNIT:
Power supply:
The parent unit can be powered directly by the included re-
chargeable battery or via the supplied power adapter. As soon
as you connect the power adapter, it will charge the battery
allowing for mobile use of the parent unit.
Battery:
1. Open the battery com-
partment by sliding and
clicking off the battery
cover at the rear.
2. Connect the battery
plug in the battery
compartment according
to the gure below and
install the battery.
Only install
the supplied
rechargeable NiMH bat-
tery (3.6V, 900mAh).
Never connect the plug
or install the battery by
force.
3. Click the battery cover
back onto the parent
unit.
Power adapter:
1. Connect
the other
6V power
adapter to
the DC6V
input on the
side of the
parent unit.
(behind the
rubber cover
top)
2. Insert the adapter into a 230V wall socket.
Only use the supplied power adaptor with model number
S003IV0600060.
You can recharge the battery with the parent unit either
switched on or off, although charging the battery with the
parent unit switched off will take less time.
Charging:
The battery will be charged as soon as you connect the power
adapter and insert it into a 230V wall socket.
For initial use, charge the battery for at least 15 hours,
even if the indicator shows a fully charged battery.
The charging circuit for the battery is managed electroni-
cally and there is no risk of overcharging, this allows you
to leave the adapter connected at all times.
In case you will not use the set for a longer period of time
(>2 months), please make sure to disconnect the adapter
from the wall socket and remove the battery from the par-
ent unit. When starting to use the set again, make sure to
properly charge the battery.
Make sure nobody can trip or fall over the adapter cable.
You can bundle cables that are too long with tape or
cables ties available specically for this purpose.
Battery indication:
Upper part of the display: (only with the parent unit switched
on)
: no battery installed, parent unit is powered directly
through the adaptor
: battery is full
: battery is nearly empty
: battery is charging
Middle part of the display: (only with the parent unit switched
on)
: this symbol appears for several seconds every minute
in the last hour before the battery is exhausted.
Indicator on the parent unit:
ashes in red: battery nearly empty
remains red: battery is charging (turns off when the bat-
tery is full)
Lanyard:
You can attach a lanyard
or wristband at the top of
the parent unit. A lanyard or
wristband is not included.
USER MANUAL
DVM-67
PARENT UNIT:
1. visual sound indica-
tion, also displays the
volume level while
adjusting
2. power button, press
briey to turn the
display on or off,
press and hold for
2 seconds to turn the
parent unit on or off
3. battery indicator (see
also further in this
user manual)
4. power adaptor input
5. zoom in/out,
6. power indicator
7. function button:
MENU/SELECT:
to open the menu and
to conrm selections
VOL , VOL , and
: various functions,
see this user manual
8. talk-back button to-
wards the baby unit
9. built-in microphone
10. Battery compartment
11. suspending option for
wrist band
12. built-in speaker
13. foldable stand
FUNCTIONS OVERVIEW
BABY UNIT:
1. Infra-red LEDs
(for night vision)
2. indicator light,
switched off when
the baby unit is
turned off, ashes
while the baby
unit is searching
for the parent
unit, remains lit
when the baby
unit is in commu-
nication with the
parent unit
3. power adaptor
input
4. power button
5. light sensor
6. camera lens
7. Volume increase
8. PAIR button (to
pair this baby unit
with the parent
unit)
9. Volume decrease
10. built-in micro-
phone
11. Built-in speaker
12. Temperature
sensor
13. Ball coupling
hinge for proper
camera orienta-
tion
14. camera feet
1
2
1
2
3
1
2
>1 - 2 m
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alecto DVM-67 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alecto DVM-67 in the language / languages: English as an attachment in your email.

The manual is 3,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alecto DVM-67

Alecto DVM-67 User Manual - German - 2 pages

Alecto DVM-67 User Manual - Dutch - 2 pages

Alecto DVM-67 User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info