633323

Alecto COA-26 Manual

23
Zoom out
Zoom in
Previous page
1/25
Next page
5. When the alarm sounds, it will turn off within 6 seconds after moving the detector to a space
with a CO concentration below 40PPM.
6. The alarm sound can be turned off by pressing the TEST / MENU button (<150PPM).
7. Every 2 minutes, the detector will automatically perform an error check.
TESTING:
When the CO detector is working under normal conditions, the sensor and siren should be tested
at least every month. Press the “TEST/MENU” button. The “POWER”,”FAULT” and “ALARM” LEDs
will illuminate. The detector will then emit 4 beeps while the red “ALARM” LED flashes 4 times.
When the display shows everything is in order.
If the sensor detects an error, the yellow “FAULT” LED will flash 2 times while 2 beep tones are
emitted. The display will now show .
RESET ALARM:
The alarm can sometimes activate because of environmental influences, for example due to smoke
with certain carbon monoxide concentrations or other chemical gaseskand. If the CO value is
below 150PPM, you can press the “TEST/MENU” button. The alarm will stop and the detector
immediately starts checking the gas again.
If the concentration is above 150PPM, it’ll be impossible to stop the alarm.
The red LED continues flashing and the siren will stop for 5 minutes.
If the concentration is still above 150PPM after those 5 minutes, the alarm will continue.
LED INDICATION:
Red LED Alarm, carbon monoxide present
Yellow LED Sensor problem
Green LED Normal functioning, the
c
PPM
TEST/MENU
= fout/faute/Fehler/fault
= test/test/Test/test
= gevaar/danger/Gefahr/danger
COA-28
CARBON MONOXIDE ALARM
lees instructies. niet schilderen.
lire les instructions. ne pas peindre.
lesen Sie die Anleitung.nicht Färben.
read instructions.do not paint.
=
vervang/remplace/Ersetz/replace
exp.07/2020
LED flashes every 45 seconds
BATTERY INFORMATION INDICATION:
1. Every 45 seconds, the battery is checked automatically.
2. Every 45 seconds, the green power LED will flash for as long as the battery power is higher
than 3.5 Volts. This means the battery capacity is sufficient. As soon as the battery power
drops below 3.5 Volts, a beep tone will be emitted when the green LED flashes briefly. At that
time, please replace the batteries as soon as possible.
The display also shows a battery capacity monitor:
Full
Half
Low
Empty
When empty batteries are indicated, the batteries should be replaced as soon as possible.
Use High Energy Alkaline batteries (3 x LR6 / 1.5V AA). Rechargeable batteries are not suitable.
With both the supplied batteries and most A brand batteries on the market, it will take
approximately one year before these are empty.
MEMORY FUNCTION:
This detector has a memory function for the following values:
• The maximum measured PPM value.
• The average PPM value of the past 24 hours.
Press and hold the “TEST/MENU” button for 10 seconds until appears in the display.
Wait 5 seconds or briefly press the “TEST/MENU” button.
the maximum measured value appears in the display.
Wait 5 seconds or briefly press the “TEST/MENU” button.
24H means that the following value is the average value of the past 24 hours.
Wait 5 seconds or briefly press the “TEST/MENU” button.
average measured value of the past 24 hours.
Wait 5 seconds or briefly press the “TEST/MENU” button.
The display shows “clear”.
Within 5 seconds, press and hold the “TEST/MENU” button for 10 seconds until
appears in the display. The memory values will now be erased.
When the batteries are replaced or briefly disconnected, the memory will also be erased.
REASON FOR SENSOR FAULT:
Faults can be caused by broken circuitry, a faulty sensor or faulty electronic parts.
SENSOR FAULT CAUSED BY CHEMICAL GASES:
When volatile chemical gases such as alcohol are the cause for error detection, this may be
corrected by switching the detector off and leave it in fresh air for 24 hours. This will restore
the sensor. If the error is not cleared after these 24 hours, the detector is faulty and should be
replaced. Don’t repair the detector yourself, but have it repaired by the importer.
When the alarm is contaminated and damaged by high concentrations of chemical gases, the
sensor could be affected. This will lead to a temporary error or permanent damage. When the
alarm sounds and you can smell a chemical gas, this could be the reason. Carbon monoxide is a
colourless and odourless gas. Chemical gases do have an odour.
The following substances and gases can cause false alarms or permanently damage the detector:
Methane, propane, iso-butane, ethylene, ethanol, alcohol, iso-propanol, benzene, toluene, acid,
ether, hydrogen, hepatic gas, sulphur dioxide, aerosol, propellant, alcohol preparation, paint,
thinner, dissolvent, bonding agents, shampoo, aftershave balm, perfume, car exhaust (cold start)
and certain cleaning agents.
USER MANUAL
… 23


Need help? Post your question in this forum.

Forumrules
1

Forum

alecto-coa-26

Reset search

  • Ik heb de batterijen verwisseld, maar nu geeft hij om de 20 sec 2 piepjes.
    Submitted on 10-3-2021 at 15:31

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alecto COA-26 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alecto COA-26 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 17.41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alecto COA-26

Alecto COA-26 User Manual - Dutch, French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info