586660

Alcatel Biloba A60 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
Telephone base and handset layout
Telephone Jack Requirements
To use this phone, you need a RJ11C type
modular telephone jack, which might look like
the one pictured here, installed in your home. If
you do not have a modular jack, call your local
phone company to nd out how to have one
installed.
CAUTION: Use only the power adapter (6Vac 300mA)
that came with this unit. Using other power adapters may
damage the unit. Contact your local distributor if you need
to order replacement for the power adapter.
Installing the Handset Battery
CAUTION: To reduce the risk of re or personal injury,
use batteries supplied with this unit, Sanik or Corun AAA
batteries (400mA 1.2V Ni-MH) which are compatible with
this unit.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE
INSTRUCTIONS.
1. Make sure the battery compartment cover is not attached with
the handset.
2. Insert the AAA rechargeable batteries in the battery
compartment, matching the
+
/
-
polarity markings.
3. Align the cover against the battery compartment and slide it
upwards until it clicks into place.
4. Charge the handset by placing it in the telephone base. The
light on the handset is on when charging.
Introduction
CAUTION: When using telephone equipment, there are
basic safety instructions that should always be followed.
Refer to the Important safety instructions in this user’s
guide for more information.
IMPORTANT: Since cordless phones operate on electricity, you
are suggested to have at least one phone in your home that is not
cordless, in case of power outage.
Parts Checklist
Make sure your package includes the items shown below.
USER’S GUIDE
Important Installation Guidelines
• Avoid sources of noise and heat, such as motors, uorescent
lighting, microwave ovens, heating appliances and direct
sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is
specically designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless
the telephone line has been disconnected at the network
interface.
• Use caution when installing or modifying telephone lines.
Telephone base installation
Install the telephone base as shown below. Make sure that the
electrical outlet is not controlled by a wall switch. If you have DSL
high speed Internet service, a DSL lter is required (not included).
Contact your DSL service provider for more information about DSL
lter.
Please Fully Charge Before Using!
For optimum battery performance, charge the battery for 16
hours before use.
Settings
Ringer Volume
You can select the handset ringer volume from four levels or turn
the ringer off.
Press UP to increase or DOWN to decrease the ringer volume
when the handset is in idle mode. A beep sounds when the
volume is adjusted to the maximum or minimum level.
Ringer Tone
You can choose one of ve ringer tones for the handset.
1. Press PROG when the handset is in idle mode.
2. Press 1 to 5 to sample each ringer tone.
3. Press the number of the desired ringer tone.
4. Press MEM to conrm your selection and a conrmation tone
sounds.
Recall/Flash time
You need to set the recall/ash time to the correct setting to use
customer calling services such as call waiting service. You can set
the recall/ash time to 1, 2, or 3.
1. Press PROG when the handset is in idle mode.
2. Press 7 to set as 1.
Press 8 to set as 2.
Press 9 to set as 3.
3. Press MEM to conrm your selection and a conrmation tone
sounds.
NOTE: If you are not sure about the correct setting, contact your telephone
service provider for more information.
Dialing mode
1. Press PROG when the handset is in idle mode.
2. Press */TONE to select tone dialing or #/PAUSE to select
pulse dialing.
3. Press MEM to conrm your selection and a conrmation tone
sounds.
Reset
Press PROG followed by #1590# to restore all system settings,
except the phonebook entries, to default settings.
Telephone
line cord
AAA
rechargeable
batteries
User’s guide
Power adapter
Wall plate
Modular
telephone
line jack
UP: Press to increase the listening volume during a call; press to
increase the ringer volume when the handset is in idle mode.
DOWN: Press to decrease the listening volume during a call;
press to decrease the ringer volume when the handset is idle.
TALK/END: Press to make or answer a call; press to end a call.
MEM: Press to save a selection during setting; press to enter the
phonebook settings or dial a call from the phonebook.
PROG: Press to enter the setting menu.
REDIAL: Press to call the last dialed number.
FLASH: During a call, press to answer an incoming call if you
have subscribed to the call waiting feature from your telephone
service provider.
*/TONE: Press to switch to tone dialing temporarily if you are
using pulse dialing service.
#/PAUSE: Press and hold to add a dialing pause when entering
numbers into phonebook.
MUTE: Press to mute a call, press again to resume conversation.
PAGE: Press to page handset.
Battery
Battery
indicator
Flashing
Handset light indicator
Indicator light Status
Flashes every 10
seconds
• The handset battery is being charged
when the power is very low.
Flashes slowly • The battery is not connected to the
handset while the handset is put in
the telephone base or charger.
• The handset is using alkaline
batteries.
Flashes rapidly • There is an incoming call.
• Programming or handset registration
is in progress.
• The telephone base is paging
handset.
ON steadily • The handset is on a call.
• The handset is being charged.
Handset Telephone base
Battery
compartment
cover
DSL lter (not included)
is required if you
have DSL high speed
Internet service.
u
v
w
x
TALK/END
MEM
PROG
MUTE
FLASH
REDIAL
DOWN
UP
*/TONE
#/PAUSE
PAGE
Making calls
1. Press TALK/END when the handset is in idle mode.
2. Dial the number.
3. Press TALK/END or place the handset in the telephone base to
end the call.
Answering calls
The handset rings when there is an incoming call.
1. Press TALK/END or lift the handset from the telephone base to
answer the call.
2. Press TALK/END or place the handset in the telephone base to
end the call.
NOTE: Press #/PAUSE to temporarily silence the ringer when there is an
incoming call.
Making a call using the redial memory
The last number dialed is stored in the redial memory (maximum
of 24 digits).
Press TALK/END and then press REDIAL.
Other features during a call
Adjusting the listening volume
You can adjust the listening volume (level 1 to 5) of the handset
during a call. Press UP to increase or DOWN to decrease the
volume, a beep sounds when the volume is adjusted to the
maximum or minimum level.
Call waiting
To use call waiting, you must subscribe to call waiting service from
your telephone service provider. This feature allows you to receive
calls while you are already on a call. You will hear a call waiting
alert tone when there is a second incoming call.
1. Press FLASH to answer the second incoming call.
2. Press FLASH to switch between calls.
The light on
the handset
is on when
charging.
Battery
Battery
indicator
Flashing
+
_
www.atlinks.com
ATLINKS Europe, 22 quai Gallieni 92150 Suresnes - France
Alcatel Logo and Alcatel name are trademarks of Alcatel and used under license by Atlinks.
_
+
USER’S GUIDE
www.atlinks.com
ATLINKS Europe, 22 quai Gallieni 92150 Suresnes - France
Alcatel Logo and Alcatel name are trademarks of Alcatel and used under license by Atlinks.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alcatel Biloba A60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alcatel Biloba A60 in the language / languages: English as an attachment in your email.

The manual is 2,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info