520611
4
Zoom out
Zoom in
Previous page
1/16
Next page
4
Installation and Operating Instructions
Radiant panel heater WW 101/151/201 E
1. Important Information
Keep these instructions in a safe place and pass them on to
possible future owners.
Use device for room heating within enclosed rooms only.
Repairs and corrective measures may only be carried out by
a qualified technician.
Disconnect the power supply in the event of fault (discon-
nect the device plug or switch off the fuse).
Do not use this device next to a bathtub, shower, washbasin
or swimming pool.
The device carries the symbol shown on the right,
which indicates that the heating device must under
no circumstances be covered with any objects.
Caution! The outer surfaces of the device, and in
particular the air outlet grid, become hot during operation.
Children or persons who are not capable of operating the
heating device safely must not operate it. Ensure that child-
ren do not play with the device.
Caution! Potential dangers can arise when the device swit-
ches on automatically, e.g. devices which have been cover-
ed or blocked by objects since they were last used could
cause fires.
The heating device must not be operated in rooms where
highly flammable substances are used (e.g. solvents, etc.).
Do not lay the connecting cable across the hot device.
2. Installation
The heating device may only be installed as shown, i.e. on a
horizontal, even surface. Use on deep-pile carpets is not per-
mitted. Please exercise caution when installing it in front of
flammable objects. Installation below a wall socket is not per-
missible. Minimum clearances must be observed.
In addition, a minimum clearance of 500 mm must be maintai-
ned between flammable objects e.g. curtains, towels or heat-
sensitive plastics and the front of the unit.
Use in the bathroom
Use the device such that it is not possible for someone in the
bath or shower to touch the control elements.
In accordance with VDE 0100 Part 701, the device must not be
fitted in protected zones 0 and 1. The device must receive its
power supply via a protective residual current device (FI).
Installation of the supporting feet
Do not operate the heating device without the feet supplied
being fitted.
Model WW 101 E is supplied without casters.
Supporting feet, casters and the
two fixing screws are provided
loose.
Screw down supporting feet as
shown and attach casters if re-
quired.
Wall mounting
The heating device must be ali-
gned horizontally and installed on
a vertical wall (see illustration).
Make sure that the inflow and out-
flow of air at the top and bottom of
the device are unimpeded
.
- Drill fixing holes for the two wall
brackets at distance "A" and
plug.
- Screw down wall brackets and
attach heater.
3. Electrical Connection
The voltage specified on the type plate must match the local
mains voltage.
If the power cord of this device is damaged, it must be replaced
by the manufacturer, the manufacturer's after-sales service or
a similarly qualified person, in order to prevent risks.
The device plug must always be accessible. In order to avoid
hazards due to inadvertent resetting of the thermal cut-out, this
appliance must not be supplied through an external switching
device, such as a timer, or connected to a circuit that is regu-
larly switched on and off by the utility company.
Model WW 101 E WW 151 E WW 201 E
Dimension A 286 mm 486 mm 686 mm
Dimension B 635 mm 835 mm 1035 mm
GB
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AKO WW 101 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AKO WW 101 E in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info