520580

AKO BK 1201 Manual

3
Zoom out
Zoom in
Previous page
1/12
Next page
3
EN
Installation and Operating Instructions
Infrared Heater BK 1201, BK 2001, BS 1201, BS 1801
1. Important Information
Keep these instructions in a safe place and pass them on to
possible future owners.
• The device must not be used in industrial areas, and may
only be used within enclosed rooms.
• The device may only be installed and repaired by a qualified
electrician in accordance with the applicable safety
regulations.
• Disconnect from the power supply in the event of a fault.
• Do not cover the heating device with any objects
- fire hazard!
• Observe the minimum clearances.
• Caution! The outer surfaces of the device are hot
during operation.
• Do not use the device as a changing table heater!
• Do not leave the heating device unattended when in use.
This applies particularly with small children or persons with
impaired health who are not able to vacate the radiation
area or the room when the temperature reaches an exces-
sive level.
• Children or persons who are not capable of operating the
device safely must not operate the heating device.
• Ensure that children do not play with the device.
• Do not operate the heating device in rooms where highly
flammable substances are used (e.g. solvents etc).
Minimum Clearances, Notes on Installation
The minimum clearances must be observed.
In addition, a minimum clearance of 65 cm must be observed
in front of the device.
Inflammable objects must not be placed in the radiation area of
the heating device.
The heating device must be aligned horizontally and installed
on a vertical wall (see illustration).
The device must be installed at a minimum height of 1.8
metres.
It is not permissible to install the device vertically or on the cei-
ling.
The protection areas defined in VDE 0100 Part 701 must be
observed during installation.
Do not place the device directly below a wall socket.
The device must be installed in such a way that it cannot be
touched by a person in the bathtub or in the shower.
The supply connection socket must be accessible after instal-
lation.
Installation on wooden walls is permissible.
Due to the heat radiation of the device, the surface on which
the device is installed can darken in colour.
Remove transport fastening
- Loosen the front grill screws (A) and remove the front grill.
- Remove the transport fastenings (B) from the heating ele-
ments.
- Re-attach the front grill.
Wall Mounting
To achieve the stipulated minimum installation height of 1.8
metres, the mounting holes for the wall holder must be drilled
at a height of 1.9 metres.
- Loosen the screw on the connection compartment cover
and remove the cover.
- Fold the radiator forward.
- Mark and drill the mounting holes on a vertical wall and in-
sert dowels.
- Insert spacers with screws into the openings of the wall hol-
der and screw the device into place.
2. Electrical Connection
Heating device must be earthed!
Connect to permanently installed wiring only.
Cable must not be laid in the radiation area of the heating de-
vice and must not be in contact with the device’s casing.
The voltage specified on the type plate must match the mains
voltage. It is recommended that a separate circuit be provided
for the power supply. A separator with a minimum contact ope-
ning of 3mm must be provided on each pole in the permanently
connected electrical installation (e.g. a circuit breaker).
A
A
B
B
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AKO BK 1201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AKO BK 1201 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 6,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info