630562

Akai APC20 Manual

5
Zoom out
Zoom in
Previous page
1/20
Next page
5
5. TRACK CONTROL FADERS – These faders control the VOL, PAN, SEND1-3 and USER1-3 levels of
the current 8 tracks and Master. Select what the faders control by holding SHIFT and pressing the
corresponding RECORD ARM / FADER MODE button above them.
6. TRACK ACTIVATORS – When lit, the current corresponding track is active. Pressing a button will
mute it (the button will become unlit). Press it again to activate it.
7. SOLO / CUE – Solos the selected track, sending it to the Cue Output. Press it again to un-solo it.
8. RECORD ARM / FADER MODE – Arms the selected track for recording. Press it again to disarm it.
Hold down SHIFT and press one of these buttons to select what the TRACK CONTROL FADERS
control (e.g., VOL, PAN, SEND1, etc.).
9. CUE LEVEL – Controls the volume sent to the Cue Output and the volume of sample auditioning.
NAVIGATION / TRACK SELECTION
These control specific functions in Ableton Live. When SHIFT is held down, pressing one of these buttons will
select a track – 1-8 or MASTER.
10. TRANSPORT CONTROLS – These transport controls – PLAY, STOP, and REC – represent the same
functions in the software.
11. MIDI OVERDUB – Turns MIDI Overdub on or off.
12. BANK SELECT – These pads move the
cursor/selection in Ableton Live by one track (left
or right) or by one scene (up or down). Holding
SHIFT while pressing this pad will move the
selection by 8 tracks (left or right) or by 5 scenes
(up or down), effectively changing the Clip
Launch View (see #1).
13. NOTE MODE – Press this button to put the CLIP LAUNCH / SESSION OVERVIEW buttons into Note
Mode. In Note Mode, the 8x5 grid will be divided into two equal halves with each button representing a
note in Ableton Live's Drum Rack. Moving left-to-right and bottom-to-top within the left half of the grid,
the buttons ascend chromatically (C1, C#1, D1, D#1, etc.) from C1 to G2. The right half of the grid
ascends similarly from G#2 to D#3. (This is ideal for using with Drum Rack, but it can also be used to
play melodic lines with any MIDI device.)
REAR PANEL OVERVIEW
1. POWER ON / OFF – Turns the APC20
on or off.
2. DC POWER ADAPTER INPUT – Plug in
the included 12V–2A DC power adapter
here.
3. USB CONNECTION – Plug a standard
USB cable into this outlet and into the USB port of your computer. This connection is used to send and
receive MIDI data to and from your computer.
4. POWER ADAPTER RESTRAINT – You can secure a power adapter cord to this restraint to prevent
accidental unplugging.
Note: In the software, a red rectangle around an
8x5 grid of clips represents APC20's current Clip
Launch View. You can change/shift the Clip
Launch View with APC20's controls (e.g. SHIFT
+ BANK SELECT).
1234
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Akai APC20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Akai APC20 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info