496440
15
Zoom out
Zoom in
Previous page
1/20
Next page
En
ENGLISH
15
DOLBY SURROUND AND DTS
SURROUND
ADJUSTING SPEAKER LEVEL
BALANCE
SUBWOOFER
+,-
CENTER
+,-
REAR +,-
BALANCE
BALANCE
JOG +,-
MANUAL
SELECT
The unit is equipped with a built-in test signal generator called a
noise sequencer for easy balance adjustment of all five channels.
The sequencer outputs a noise signal that “travels” from channel
to channel, enabling the simple adjustment of sound level to
achieve the same apparent loudness, at your listening position,
from each channel.
Preparation
Before adjusting the speaker level balance, be sure to set
the speaker size, distance and existance correctly.
Before adjusting the speaker level balance, turn off the DSP
surround system.
Operate the unit while playing the source recorded in Dolby
Digital surround or Dolby Pro Logic.
1Turn SURROUND on.
2 Press and hold MANUAL SELECT on the remote
control until “L” of “L/R 0dB” starts to flash.
A noise signal is sent to each channel in turn at the interval of
2 seconds as follows:
L/R 0dB
C 0dB
L/R 0dB
S 0dB
S 0dB
*L or R flashes to indicate one of the front speakers from
which the noise signal is output.
3 Adjust the sound level of the center and surround
speakers.
While “C” or “S” flashes in the display, press JOG + or - on
the remote control so that the sound level of the center or
surround speakers matches that of the front speakers.
The blance of the front speakers can be adjusted as well while
L/R” is displayed.
4 Press MANUAL SELECT again to stop the noise
signal.
NOTE
When the noise signal cycles through all the speakers for ten
times, the noise singal stops automatically.
When the center speaker and/or surround speakers are set to
NONE”, their level balance cannot be adjusted. (“C 0dB” and “S
0dB” are not displayed.)
About the channels
The left and right front speakers create the stereo effect.
The center speaker helps precise sound positioning over a broad
sound field.
The surround speakers enhance the “depth” of the sound field.
CHANGING SPEAKER VOLUME
TEMPORARILY
According to the software played or your preference, you can
change the sub woofer, center speaker and surround speakers
volume temporarily.
Press SUBWOOFER +/-, CENTER +/- or REAR +/-
on the remote control.
Each speaker level can be changed within the range from –10
dB to +10 dB at 1 dB steps.
To restore the volume and balance to the default value
Press and hold BALANCE until “LVL RESET” is displayed.
All the speaker volume as well as the left and right balance of
the front and surround speakers are reset to the default value
(0 dB).
(Left front speaker)*
(Center speaker)
(Right front speaker)*
(Right surround speaker)
(Left surround speaker)
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aiwa AV-NW31 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aiwa AV-NW31 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info