574671
92
Zoom out
Zoom in
Previous page
1/96
Next page
ANSCHLUSS
ABFLUSSSCHLAUCH
1. Befestigen Sie den Kondensat-Abflussschlauch am
Wellschlauch in der Nut hinten am Innenteil.
2. Binden Sie den Abflussschlauch
mit der Kältemittelleitung und den
Elektrokabeln zusammen.
3. Stellen Sie sicher, dass der
Kondensat-Abflussschlauch
durchgängig nach unten abfällt.
4. Vermeiden Sie bei der
Installation des
Abflussschlauches
Wasserverschlüsse und U-
Bogen. Das Ende des
Abflussschlauches sollte nicht im
Wasser versenkt sein.
5. Für einen Austritt auf der linken
Seite verlegen Sie den
Abflussschlauch unten in der
rückwärtigen Nut des Innenteils.
6. Wenn die Installation lange
horizontale Abschnitte erfordert,
muss am oberen Punkt des
Schlauches ein Auslass
vorgesehen sein, um ein
Überlaufen der Abflusswanne zu
verhindern.
Abb. 11
1. Abflussschlauch
2. Rohrschelle
3. Gefälle
Abb. 12
1. Wasserverschluss
2. U-Bogen
3. Ende im Wasser
versenkt
Abb. 13
1. Elektrokabel
2. Kältemittelleitung
3. Kondensat-
Abflussschlauch
4. UV-stabilisiertes,
nichtklebendes
Kunststoffband
Abb. 14
1. Auslass
2. Abfluss nach unten
3. Wasser-
Abflussschlauch
Abb. 9
Abb. 10
GERÄT AN DER MONTAGEPLATTE
AUFHÄNGEN ODER ABNEHMEN
1. Stellen Sie sicher, dass die Kältemittelleitungen, Elektrokabel
und der Kondensat-Abflussschlauch ordnungsgemäß mit
geschlossenzelligen Gummirohren (in 6 mm Stärke) isoliert und
mit UV-stabilisiertem, nichtklebendem Kunststoffband
zusammengebunden sind und führen Sie sie dann durch die
Wandöffnung.
2. Hängen Sie das Innenteil an die beiden Haken an der oberen
Kante der Montageplatte (s. Abb. 9 und 10).
3. Drücken Sie den unteren Teil des Geräts gegen die
Montageplatte, bis die Schnappbefestigungen in den
Aufnahmenuten einrasten und das Innenteil damit sicher an der
Montageplatte befestigt ist.
4. Prüfen Sie, ob das Gerät sicher befestigt ist, indem sie
versuchen, es ein wenig in Ihre Richtung zu ziehen.
5. Wenn Sie das Gerät wieder von der Montageplatte abnehmen
wollen, heben Sie es an und ziehen Sie es in Ihre Richtung.
Abb. 9
1. Innenteil
2. Schnappbefestigungen
3. Haken oben
4. Haken unten
Abb. 10
1. Montageplatte
2. Haken unten
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Airwell Florida FLO DC Inverter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Airwell Florida FLO DC Inverter in the language / languages: German as an attachment in your email.

The manual is 5,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info