603855
5
Zoom out
Zoom in
Previous page
1/164
Next page
5
ENGLISH
5. CONTROLS
The hood is tted with a control panel with
aspiration speed selection control and a
light switch to control cooking area lights.
Use the high suction speed in cases
of concentrated kitchen vapours. It is
recommended that the cooker hood suction
is switched on for 5 minutes prior to cooking
and to leave in operation during cooking
and for another 15 minutes approximately
after terminating cooking.
The control switches are located on the
hood’s front panel:
1A 1B 1C 1D 1E
A. OFF – ON push button
Press once or more to obtain the
function desired:
ON: the hood switches on to the last
speed selected.
OFF: all the functions are switched off
except the illumination.
B. Speed selection push button (extraction
power).
Press this push button once or more
to select the most suitable extraction
speed (power) (1-2-3).
C. The display shows the extraction
power selected, signalling the
saturation of the lters F.
D. Intensive speed on/off. The Intensive
speed runs for 5 minutes:
If the hood is on when the Intensive
speed is activated, the hood reverts to
previous speed after 5 minutes.
If the hood is off when the Intensive
speed is activated, the hood will be
turned off after 5 minutes.
To interrupt the Intensive speed, press
button A or B.
E. Light ON/OFF
Should the hood or the controls fail to
operate: disconnect the power supply for at
least 5 seconds, then turn the hood back
on again.
Grease and charcoal lter maintenance
indicator
This hood is tted with a device that
indicates when maintenace of lters should
be done.
If the hood is to be used with a charcoal
lter, the saturation
indicator light must be enabled as follows:
Set the hood in “OFF”.
Pressing keys B and D simultaneously for
three seconds, LED F lights up and begins
to ash the 1st speed led. After 1 second
the 2nd speed led also ashes and the
system emits a sound signal (-Beep-) to
indicate setting taking place.
To remove the charcoal lter signal press
push buttons B and D simultaneously for 3
seconds. LED F lights up and begins to
ash the 1st speed led (grease lter) and
the 2nd speed led. After 1 second, only
the 1st speed led continues to ash. The
system emits a sound signal (-Beep-) to
indicate setting taking place.
Grease lter LED
The 1st speed led (+ led F) ashes, when it
is time to clean the grease
lter.
Always comply with the maintenance
instructions for the grease lter.
Charcoal lter LED
The 2nd speed led (+ led F) ashes,
when the charcoal lter needs to be
cleaned or replaced.
Resetting the saturation indicator
After cleaning or replacing the lters, press
button A for 3 seconds until the 1st speed
led or the second speed led stops ashing.
The F LED also turns off.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG X79263MD1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG X79263MD1 in the language / languages: French as an attachment in your email.

The manual is 20,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info