463270

AEG WS 715-125 Manual

2
Zoom out
Zoom in
Previous page
1/57
Next page
ENGLISH 2 WS 650-115, WS 715-115, WS 715-125, WSE 800-125
Introduction
You demand the best and buy quality - quality provided by Atlas Copco. We have
built for you a reliable and lasting tool. Working effectively and without endangering
your health is only possible if this instruction for use is read carefully before first us-
ing the tool. We want to satisfy our customers and would like you to buy again AEG
Electric Power Tools from Atlas Copco.
Technical Data
Safety advice ■ Please pay attention to the safety instructions in the attached leaflet!
■ Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
■ Always disconnect the plug from the socket before carrying out any work on the ma-
chine.
■ Only plug-in when machine is switched off.
■ Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
■ Before use check machine, cable, and plug for any damages or material fatigue. Re-
pairs should only be carried out by authorised service agents.
■ Allow the machine to come to a stop before putting down.
■ Dust that arises when working in stones with crystalline silicic acid can damage your
health. Do not work on any material containing asbestos. Please note the safety reg-
ulations, VBG, of the employer’s liability insurance association.
■ Never reach into the danger area of the machine when it is running.
■ Always wear safety goggles and ear protectors when working with this machine. It
is further recommended to wear safety gloves, apron, as well as sturdy non-slipping
shoes.
■ Always use the additional handle.
■ Always use the protecting cap when roughing-down and separating.
■ Only use tools whose permitted speed is at least as high as the highest no-load
speed of the machine.
■ Check grinding tools before use. The grinding tool must be properly mounted and
turn freely. Perform a test run for at least 30 seconds without load. Do not use dam-
aged, out of round or vibrating grinding tools.
■ When grinding metal, flying sparks are produced. Take care that no persons are en-
dangered. Because of the danger of fire, no combustible materials should be locat-
ed in the vicinity (spark flight zone). Do not use dust extraction.
■ Due care should be taken that no sparks or sanding dust flying from the workpiece
come into contact with you.
■ Pay attention to the dimensions of the grinding disc. The mounting hole diameter
must fit the mounting flange without play. Do not use reducer pieces or adapters.
■ Never use a cutting disc for grinding. Do not subject cutting discs to side pressure.
■ When separating stone the guide shoe must be used!
Type WS 650- WS 715- WSE 800-
115 115 125 125
Nominal power (W) 650 710 710 800
Min. no-load speed (min
-1
) 2700
Max. no-load speed (min
-1
) 10000 10000 10000 10000
Grinding disk diameter (mm) 115 115 125 125
Thread of work spindle M14 M14 M14 M14
Weight (kg) 1,5 1,5 1,5 1,5
Speed control
•
No-load speed limiter
•
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG WS 715-125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG WS 715-125 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 1,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info