463235
77
Zoom out
Zoom in
Previous page
1/79
Next page
74
中文
中文
TS 250 K
输入功率 ................................................................... 1800 W
额定电流强度 ............................................................ 7,5 A
无负载转速 .............................................................. 4800 min
-1
锯刀直徑 x 锯刀孔直徑 ................................250 x 30 mm
锯片厚度 ...................................................................... 1,8 mm
切深在 90 ................................................................ 90 mm
切深在 45 ................................................................ 62 mm
不含电线重量 ............................................................. 41 kg
噪音/振动信息
本测量值符合 EN 61029 条文的规定。
器械的标准A-值噪音级为:
音压值 (K=3dB(A)) ......................................................... 98 dB(A)
音量值 (K=3dB(A)) ....................................................... 111 dB(A)
请戴上护耳罩!
注意!务必仔细阅读所有安全说明和安全指
示(应注意阅读附上的小册子)。 如未确实 遵
循警告提示和指示,可能导致电击、火灾並且/
或其他的严重伤害。 妥善保存所有的警告提示
和指示,以便日后查阅。
特殊安全指示
请戴上耳罩。 所发生的噪声会导致听力损失。
操作机器时务必佩戴护目镜。最好也穿戴工作手
套、坚固防滑的鞋具和工作围裙。
工作中产生的废尘往往有害健康,最好不要让此
类物质接触身体。操作机器时请使用吸尘装置并
佩戴防尘面罩。彻底清除堆积的灰尘,例如使用
吸尘器。
户外插座必须连接剩余电流防护开关。这是使用
电器用品的基本规定。使用本公司机器时,务必
遵守这项规定 (FI, RCD, PRCD)。
在机器上进行任何修护工作之前,务必从插座上
拔出插头。
使用之前,先检查机器、电源电线、延长线和插
头是否有任何坏损。损坏的零件只能交给专业电
工换修。
确定机器已经关闭了才可以插上插头。
电源线必须远离机器的作业范围。
务必确保机械的安全位置。
不得使用损坏或变形锯条。
只能使用按规定研磨的锯片。
锯刀片的规格如果与本说明书提供的规格不符,
请勿使用。
锯刀刀身的厚度不可以大过分离楔的厚度。而锯
齿的厚度则必须大于分离楔的厚度。不可拆除
分离楔。
为了最大程度地降低噪音,必须磨快刀具,并且
要正确地安放降低噪音的组件(如盖罩等)。
只能使用符合EN 847-1标准的刀具。
刀具必须放在合适的容器中运输和保管。
选择适合加工物料的锯片。
遵照锯片上标示的最高转速限制使用锯片。
不可以使用高速钢製造的锯片。
固定锯片时,只能使用机器附带的法兰和说明书
上标示的法兰。
取下夹紧扳手。在将设备开机之前,要总是核实
夹紧扳手已经取下。
本台式圆锯只能用于切割说明书中载明的物料。
锯切时,不可能安全地握住有圆形或不均匀形横
截面(木柴等)的工件,因此切勿锯切这种工
件。竖起锯切扁平工件时,务必使用适合的辅助
挡板,以确保安全的工件导引。
一察觉机器内部、防护装备或锯片发生故障,务
必马上通知负责安全事宜的人员。
不得将圆锯用于工件的开槽(工件内的开槽)。
只有在使用合适的防护装置例如锯台上的通道防
护装置时,才允许进行折边和开槽工作。
首次使用机器之前,必须详细阅读使用指南并确
实遵照指示使用机器。
务必使用机器的安全保护设备。
使用台式圆锯之前,先检查防护罩是否运作正常
并且正常安装。防护罩应可以自动转回。
不可以擅自掀开摇摆防护罩,并固定防护罩。
手不可以靠近转动中的刀片。
如果机器仍在运转,切勿清除其上的木屑或金
属碎片。
机械工作并锯头不在静止位置时,不得将锯屑或
其他工件部分从锯切区清除。
如 果 锯 片 卡 住 了 , 或 锯 割 过 程 因 为 任 何
原 因 突 然 中 断 了 ,必 须 马 上 放 鬆 起 停 开
关 , 並 静 待 插 在 工 件 中 的 锯 片 完 全 停 止
运 动 。 只 要 锯 片 仍 继 续 运 动 , 千 万 不 可
尝 试 著 从 工 件 中 拔 出 锯 片 , 或 向 后 抽 拉
圆 锯,否则可能发生反弹 。 找 出 导 致 锯 片 卡
住 的 原 因 , 並 设 法 排 除 障 碍 。
使用辅助工具以提高工作安全,例如支撑及压紧
装置,导引板和推杆等!
为了降低切割片被卡住时发生反冲的风险,对板
材或者较大的工件要予以支撑。工件较大时,工
件会由于自身的重量而弯曲。对工件要从两侧
支撑,包括在切割线附件的支撑和在工件棱边
的支撑。
要检查平行切锯导轨是否和锯片相平行。
如果要进行横锯,要将平行导轨取下。
得确保地板上无锯屑、锯末等材料剩余。
得更换磨损的锯台插件。
根 据 使 用 说 明 书 上 的 描 述 调 整 开 缝 楔 子
。 留 错 空 隙 、 位 置 不 正 确 和 校 准 错 误 ,
都 会 影 响 开 缝 楔 子 防 止 反 弹 的 功 能 。
技术数据 台式圆锯
77


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG TS 250 K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG TS 250 K in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info