463219
3
Zoom out
Zoom in
Previous page
1/31
Next page
5
.............6 mm
.............6 mm
..........3,5 mm
.........180 min
-1
(700min
-1
*)
....0,5-1,7 Nm (2 Nm)
..........1-3 Nm (6 Nm)
...... 2,4 V
....0,5-6,5 mm
..........0,4 kg
ENGLISH
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the
attached leaflet!
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Sawdust and splinters must not be removed while the
machine is running.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
Dust that arises when working on material containing
asbestos or stonework containing crystalline silicic acid is
harmful to the health. Please follow accident prevention
regulations.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household
refuse or by burning them. AEG Distributors offer to retrieve
old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System 2000 chargers for charging System 2000
battery packs. Do not use battery packs from other systems.
No metal parts must be allowed to enter the battery section
of the charger (short circuit risk).
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
SPECIFIED CONDITIONS OF USE
The battery drill/screwdriver is designed for drilling and
screwdriving for independent use away from mains supply.
Do not use this product in any other way as stated for
normal use.
TECHNICAL DATA
Drilling capacity in steel ....................................................................................................
Drilling capacity in wood ...................................................................................................
Wood screws (without pre-drilling) ...................................................................................
No-load speed ..................................................................................................................
Torque
Soft wood (max) ............................................................................................................
Steel plate (max) ...........................................................................................................
Battery voltage .................................................................................................................
Drill opening range * .........................................................................................................
Weight with battery ...........................................................................................................
BATTERIES
New battery packs reach full loading capacity after 4 - 5
chargings and dischargings. Battery packs which have not
been used for some time should be recharged before use.
Temperatures in excess of 50
o
C (122
o
F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 50260, EN 55014-1, EN 55014-2, in
accordance with the regulations 98/37/EC, 89/336/EEC
Volker Siegle
Manager Product Development
MAINTENANCE
Use only AEG accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Remove the battery pack before starting
any work on the machine.
* with high speed chuck (accessory)
Typically the A-weighted sound pressure level of the tool is less than 70 dB (A).
The noise level when working can exceed 85 dB (A).
Typically the hand-arm vibration is below 2.5 m/s
2
.
Measured values determined according to EN 50 260.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG SE 2.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG SE 2.4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info