563600
60
Zoom out
Zoom in
Previous page
1/64
Next page
60
Störungssuche
PROBLEM URSACHE PROBLEMBESEITIGUNG
Schneefräse 1. Das Benzin-Absperrventil (falls vorhanden) 1. Stellen Sie das Benzin-Absperrventil auf Position “OPEN”.
springt nicht an ist auf Position “OFF”.
2. Der Sicherheitszündschlüssel steckt nicht. 2. Sicherheitszündschlüssel einstecken.
3. Benzin leer. 3. Füllen Sie den Benzintank.
4. Gashebel auf Position “STOP”. 4. Stellen Sie den Gashebel auf Position “FAST”.
5. Choke auf Position “OFF”. 5. Stellen Sie ihn auf Position “FULL.
6. Einspritzvorrichtung nicht betätigt. 6. Spritzen Sie gemäß der Anleitung im Abschnitt Bedienung dieses Handbuchs ein.
7. Motor ist geflutet. 7. Warten Sie einige Minuten bis zum Neustart, NICHT einspritzen.
8. Zündkabel ist nicht verbunden. 8. Verbinden Sie das Zündkabel mit der Zündkerze.
9. Zündkerze defekt. 9. Erneuern Sie die Zündkerze.
10. Benzin ist abgestanden. 10. Entleeren Sie den Benzintank und füllen Sie frisches, sauberes Benzin nach.
11. Wasser im Benzin. 11. Entleeren Sie den Benzintank und den Vergaser und füllen Sie frisches Benzin nach.
Motorausfall 1. Zündkabel ist lose. 1. Schließen Sie das Zündkabel wieder an.
2. Zu viel Schnee gefräst. 2. Verringern Sie die Geschwindigkeit und die Breite der Räumungsbahnen.
3. Entlüftungsloch am Benzintankdeckel 3. Entfernen Sie Eis und Schnee vom Entlüftungsloch am Benzintankdeckel.
ist verstopft.
4. Schalldämpfer ist verschmutzt oder blockiert. 4. Reinigen oder erneuern Sie den Schalldämpfer.
Motor läuft im 1. Choke ist auf Position “FULL”. 1. Stellen Sie den Choke auf Position “OFF”.
Leerlauf oder läuft 2. Benzinleitung blockiert. 2. Reinigen Sie die Benzinleitung.
unregelmäßig. 3. Benzin ist abgestanden. 3. Entleeren Sie den Benzintank und füllen Sie frisches, sauberes Benzin nach.
4. Wasser im Benzin. 4. Entleeren Sie den Benzintank und den Vergaser und füllen Sie frisches Benzin nach.
5. Vergaser muss neu eingestellt oder 5. Wenden Sie sich an eine qualifizierte Kundendienststelle.
erneuert werden.
Übermäßiges 1. Lose Teile oder Schäden an den 1. Ziehen Sie alle Schrauben fest an. Ersetzen Sie beschädigte Teile.
Vibrieren Einzugsschnecken oder am Antriebsrad. Sollten die Vibrationen weiterhin auftreten, wenden Sie sich an eine
qualifizierte Kundendienststelle.
Anreißstarter läßt 1. Anreißstarter eingefroren. 1. Siehe “WENN DER ANREIßSTARTER EINGEFROREN IST“
sich nur schwer im Abschnitt Bedienung dieses Handbuchs.
anziehen
Fahrantriebsverlust 1. Antriebsriemen ist abgenutzt. 1. Überprüfen/ersetzen Sie den Antriebsriemen.
/verringerte 2. Antriebsriemen ist von Riemenscheibe gerutscht. 2. Überprüfen/reinstallieren Sie den Antriebsriemen.
Fahrgeschwindigkeit 3. Reibrad ist abgenutzt. 3. Wenden Sie sich an eine qualifizierte Kundendienststelle.
Kein Schneeauswurf 1. Einzugsschneckenriemen ist von Riemenscheibe gerutscht. 1. Überprüfen/reinstallieren Sie den Einzugsschneckenriemen.
mehr oder 2. Einzugsschneckenriemen ist abgenutzt. 2. Überprüfen/ersetzen Sie den Einzugsschneckenriemen.
verlangsamter 3. Auswurfrinne verstopft. 3. Reinigen Sie die Auswurfrinne.
Schneeauswurf 4. Einzugsschnecken/Antriebsrad blockiert. 4. Entfernen Sie Geröll oder Fremdkörper von den
Einzugsschnecken/dem Antriebsrad.
Troubleshooting
PROBLEM CAUSE CORRECTION
Does not start 1. Fuel shut-off valve (if so equipped) in “OFF” position. 1. Turn fuel shut-off valve to “OPEN” position.
2. Safety ignition key is not inserted. 2. Insert safety ignition key.
3. Out of fuel. 3. Fill fuel tank.
4. Throttle in “STOP” position. 4. Move throttle to “FAST” position.
5. Choke in “OFF” position. 5. Move to “FULL position.
6. Primer not depressed. 6. Prime as instructed in the Operation section of this manual.
7. Engine is flooded. 7. Wait a few minutes before restarting, DO NOT prime.
8. Spark plug wire is disconnected. 8. Connect wire to spark plug.
9. Bad spark plug. 9. Replace spark plug.
10. Stale fuel. 10. Drain tank and refill with fresh, clean fuel.
11. Water in fuel. 11. Drain fuel tank and carburetor and refill tank with fresh gasoline.
Loss of power 1. Spark plug wire loose. 1. Reconnect spark plug wire.
2. Throwing too much snow. 2. Reduce speed and width of swath.
3. Fuel tank cap vent hole is clogged. 3. Remove ice and snow from fuel tank cap vent hole.
4. Dirty or clogged muffler. 4. Clean or replace muffler.
Engine idles 1. Choke is in FULL position. 1. Move choke to OFF position.
or runs 2. Blockage in fuel line. 2. Clean fuel line.
roughly 3. Stale fuel. 3. Drain tank and refill with fresh, clean fuel.
4. Water in fuel. 4. Drain fuel tank and carburetor and refill tank with fresh gasoline.
5. Carburetor is in need of adjustment or overhaul. 5. Contact a qualified service center.
Excessive 1. Loose parts or damaged augers or impeller. 1. Tighten all fasteners. Replace damaged parts.
vibration If vibration remains, contact a qualified service center.
Recoil starter 1. Frozen recoil starter. 1. See “IF RECOIL STARTER HAS FROZEN”
is hard to pull in the Operation section of this manual.
Loss of traction 1. Drive belt is worn. 1. Check / replace drive belt.
drive / slowing 2. Drive belt is off of pulley. 2. Check / reinstall drive belt.
of drive speed 3. Friction drive wheel is worn. 3. Contact a qualified service center.
Loss of snow 1. Auger belt is off of pulley. 1. Check / reinstall auger belt.
discharge or 2. Auger belt is worn. 2. Check / replace auger belt.
slowing of 3. Clogged discharge chute. 3. Clean snow chute.
snow discharge 4. Augers / impeller jammed. 4. Remove debris or foreign object from augers / impeller.
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG PSB300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG PSB300 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info