9975
52
Zoom out
Zoom in
Previous page
1/56
Next page
Fix the base firmly to the
floor using four appropriate
countersunk screws
(see Fig. H).
With the appliance
installed adjust all four
feet ensuring the machine
is stable, and a clearance
of approximately 5 mm is
left between the top of the machine and the underside of the work-
top.
A final check for stability should be carried out with the machine on
spin with a load, this will identify the need for any further fine adjust-
ment to the feet.
A strip of beading approximately 605 mm W, x 5 mm H, x 25 mm D
must be screwed down into the base directly in front of the machine’s
feet, this will provide additional security.
If required an additional door magnet, part number 1242394-00/3 and
disc, part number 1242393-00/5 are available from spare parts.
53
Recommendations regarding the construction and fitting of
a base when the installation requires an integrated appliance
to be raised
Where the appliance has been raised by mounting onto a wooden base pro-
vided by the installer. The material used to construct the base should have
a non slip surface, be water repellent and if possible be one solid piece.
If it is not possible to
use one solid piece,
due to the additional
height required, ensure
that any additional
strips of timber are
glued and screwed to
the underside of the
base (see Fig. F).
Position the base into
the recess with its front
edge as far forward as
the adjoining plinth
line will allow. The rea-
son for placing the
base in this position is
to allow a small strip
of beading to be fit-
ted in front of the
appliance feet.
52
Building-in
600-605
5 X 25 X 605
Hardwood strip
5 mm x 25 mm
H
490
600-605 mm
50 mm
Front edge
Top view
95 mm
490 mm
G
Building-in
600-605 mm
Front view
5 mm Hardwood strip
Additional pieces of
timber should run
from front to back
100 mm
40 mm
F
Drill four fixing holes see Fig. G
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG Lavamat 1051Vi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG Lavamat 1051Vi in the language / languages: English as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AEG Lavamat 1051Vi

AEG Lavamat 1051Vi Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info