551827
10
Zoom out
Zoom in
Previous page
1/12
Next page
10
1. Legen Sie zwei Batterien in das Batteriefach der FB. Beachten Sie die Zeichnung auf der
FB.
2. Stecken Sie den Antennenanschluß in die Antennenbuchse des Fernsehgerätes.
3. Schließen Sie den Stecker an die Steckdose des Versorgungsnetzes an und drücken Sie
die Netz- Taste auf der Vorderseite des Gerätes. Leuchtet der Bildschirm nicht auf, drücken
Sie die Tasten P+, P- oder 0,1,2..9 auf der Fernbedienung, oder die Tasten P+, P- auf der
Vorderseite des Fernsehgerätes, damit der Fernseher vom Bereitschaftsmodus zum TV-
Modus umgeschaltet wird.
4. Drücken Sie dreimal die FB- Taste MENU. Auf dem Bildschirm erscheint das Verzeichnis
Sender.
5. Drücken Sie die FB- Taste OK. Nun wird Ihr Fernsehgerät automatisch alle Sender
einstellen und speichern. Dies kann einige Minuten dauern. Nach dem Suchvorgang schaltet
das Fernsehgerät auf den ersten Programmplatz.
6. Jetzt können Sie die Programme in die gewünschte Reihenfolge bringen, mit Hilfe der
Tabelle Programm des Verzeichnisses Einstellungen, wie im Abschnitt "Ordnen der
gespeicherten Programme" (S. 7) beschrieben.
7. Nun können die Programme mit den FB- Tasten P+, P- oder 0,1,2...9, und mit den Tasten
P+, P- auf der Vorderseite des Fernsehgerätes gewählt und umgeschaltet werden.
Hinweise:
1. Bei Ausfall des Signals in der Antennenbuchse, leuchtet der Bildschirm des Fernsehgerätes
blau.
2. Bitte beachten Sie, dass in einigen Empfangsgebieten die analogen terrestrischen Fernseh-
sender (Empfang über klassische Antenne) auf digital umgestellt wurden und somit ein
Empfang über Antenne nur mit einem DVB-T Empfänger (erhältlich im Fachhandel)
möglich ist.
Kurzanleitung zur Erstinbetriebnahme und Einstellung der Programme
des Fernsehgerätes
Durch Betätigung der FB- Taste AV ein oder mehrere Male, wählen Sie den notwendigen Modus der
äußeren Signalquellen (je nach Gerättyp):
AV1, AV2 wählt den entsprechenden Bild- und Ton- Eingang in der Steckverbindung
SCART1 oder SCART2. Wird zum direkten Anschluß eines Videogerätes,
einer Satelliten- Empfangsanlage etc. benutzt.
Front AV über den Front-AV Eingang können Sie z. B. eine Videokamera anschließen.
Bitte beachten Sie, dass der Scartanschluss AV 2 parallel zum Front-AV
geschaltet ist und nicht parallel genutzt werden können, da es sonst zu
Störsignalen kommt.
RGB wählt den Signaleingang rot, grün und
blau in der Steckverbindung SCART1.
Wird zum direkten Anschluß einer Spiel-
konsole und anderer Geräte benutzt.
AV - Modus
2
20
21
1
15
Switching on
1. Remove the battery cover from the remote control unit and install two AAA (R03) type
batteries (not supplied) according to the diagram inside the battery compartment. Replace
the battery cover.
Attention: Please ensure that the polarity of the batteries is correct. Batteries are not to be disposed
of together with domestic wastes. Dispose of the used batteries at the relevant collection
bin or at your dialers. Never throw batteries into the fire.
2. Connect your aerial to the TV set.
3. Connect your TV to a 230 VAC power socket.
4. Switch on your TV with the
switch on the front panel. The red light will be illuminated. If
the screen does not light up, press a button P - or P+ on the front of the television set or
any of the keys P-, P+, 0, 1, ..., 9 on the remote control.
Notes:
1. After switching the television set on by using
front panel button, the set switches to the
same mode it was before switching of by this button. If TV set was switched off by using
the remote control key POWER, it switches to standby and the indicator on the front panel
turns red.
2. After switching television set from standby to operating status, the red indicator go down.
Control of TV set by using MENU tables
Your television set is controlled by using MENU tables Picture,
Audio, Install, Setup. These tables appear on the screen after
pressing remote control button MENU one or more times. The
television set parameters and their values are arranged in these
MENU tables.
The line of table with required parameter you can select by using the
remote control keys P+ or P-, and to change this parameter by using
keys V+ or V-. MENU tables from the TV screen disappears
after pressing the remote control key MENU one or several times or
about after 5 seconds after the last action in these tables.
Note: The selected line in table is highlighted in red.
Selecting the menu language
The on-screen menu has several languages. The selection of language is the
following:
1.
Press the MENU key on the remote control 4 times. The menu Setup
will appear on the screen.
2. Use the P+ or P- to select Language.
3. Press OK. The table with languages will appear on the screen.
4. Use the P+ or P- to select the language you require.
5. Press the MENU key twice to switch off the Setup menu.
English
Franšais
Deutsch
Italiano
Norsk
Svenska
Nederlands
Español
PORTUGUÊS
Dansk
Suomi
Greek
Setup
Timer
Organize
Function
Language
English
Franšais
Deutsch
Italiano
Norsk
Svenska
Nederlands
Español
PORTUGUÊS
Dansk
Suomi
Greek
Setup
Timer
Organize
Function
Language
(AV2)
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG CTV 4833 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG CTV 4833 in the language / languages: German as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info