648321
1
Zoom out
Zoom in
Previous page
1/4
Next page
M O N TA G E A N L E I T U N G
1
© 2012 OJ Electronics A/S - EHT Haustechnik GMBH
Developed by OJ Electronics A/S - www.ojelectronics.com
Typ ATE 50
Deutsch
ANWENDUNG
ATE 50 ist ein kompaktes Thermostat zur Tem-
peraturregelung.
PRODUKTPROGRAMM
ATE 50 mit Skalenbereich von -10/+50 °C
Zubehör
Fühler:
ATF 5 : NTC Sensor zur Außentemperatur-
erfassung.
AF 5-2,5 : NTC-Anlegefühler für Rohrbegleit-
heizung.
FUNKTION
ATE 50 ist ein 2-Punkt-Thermostat mit einstell-
barer Dierenztemperatur (siehe technische
Daten) zur Regelung der Temperatur. Wenn
die Fühlertemperatur unter der Thermostat-
einstellung Minus Dierenztemperatur ist,
wird das potentialfreie Relais aktiviert (schließt
zwischen Klemme 4 und 5) und Heizung wird
eingeschaltet. Die Leuchtdiode leuchtet rot auf.
Wenn die Fühlertemperatur die eingestellte
Temperatur Plus Dierenztemperatur übersteigt,
schaltet das Relais zwischen Klemme 4 und 5
und das Heizelement wird gleichzeitig mit der
Leuchtdiode ausgeschaltet.
Da der ATE 50 mit Wechselkontakte versehen
ist, kann der ATE 50 auch als Kühlthermostat
eingesetzt werden, wenn das Kühlelement zwi-
schen Klemme 3 und 5 angeschlossen wird.
CE PRÜFZEICHEN
Gemäß folgende Normen:
NSR/EMV: EN 60730-2-9.
Das Produkt darf erst in Betrieb genommen
werden, nachdem sichergestellt ist, dass die
Gesamtinstallation die geltenden Forderungen
der Direktive erfüllt.
Nachdem das Produkt nach den Anweisungen
dieser Bedienungsanleitung und den Instal-
lationsvorschriften montiert ist, ist es von der
Werkgarantie umfasst.
Ist das Produkt z. B. im Transport beschädigt
worden, ist es vom qualifizierten Personal zu
besichtigen und zu prüfen, bevor das Produkt
ans Netz angeschlossen wird.
TEKNISCHE DATEN
Betriebsspannung ... 230V AC ±10%, 50-60 Hz
Max. Sicherung ..........................................10A
Ausgangsrelais ....................... Schaltrelais 10A
Dierenz - einstellbar .......................... 0,3-6 °C
Betriebstemperatur ............................. 0/+50 °C
Leistungsaufnahme .................................... 3VA
Gewicht ...................................................170 g
Abmessungen (HxBxT) ............... 86x36x58 mm
Gehäuseschutzart ....................................IP 20
Temperaturfühler ........................... NTC-Fühler
KLASSIFIKATION
Das Produkt ist ein Klasse II Gerät (verstärkte
Isolation) und das Produkt ist an die folgenden
Leiter anzuschliessen:
1) Phase (P/L1)
2) Nulleiter (N)
TEMPERATUREINSTELLUNG
Der ATE 50 hat einen Skalenbereich von
-10/+50°C. Der Thermostat ist mit einer
Leuchtdiode versehen, die rot aufleuchtet, wenn
die Heizung eingeschaltet ist. Der Thermostat
auf max. Temperatur drehen, bis die gewün-
schte Raumtemperatur erreicht ist. Dann den
Thermostat herunterdrehen, bis die Leuchtdiode
erlischt. Nach 1-2 Tagen kann eine Feinjustie-
rung notwendig sein.
MONTAGE
DIN-Schienen Montage. Anschluss laut Abb. 1.
FÜHLER
Der Fühler ist ein NTC-Fühler. Die Fühler ATF 5
und AF 5-2,5 können für den ATE 50 mit Ska-
lenbereich -10/+50 °C, eingesetzt werden. Den
Fühler nach Anwendungsgebiet wählen.
Bodenfühler: Der Bodenfühler wird in einem
Installations-Rohr in den Estrich verlegt. Das
Installationsrohr wird am Ende abgedichtet und
so nahe wie möglich unter der Oberfläche in
den Estrich oder die Ausgleichschicht einge-
gossen.
Wenn notwendig kann das Fühlerkabel mit
einem handelsüblichen Installationskabel bis auf
100 m verlängert werden.
Raumfühler: Dieser sollte so an die Wand
montiert werden, dass die Luft frei darüber
hinweg ziehen kann. Den Montageort so
auswählen, dass der Fühler nicht einer fremden
Energiequelle, wie z. B. der Sonnenbestrahlung
ausgesetzt werden kann. Den Fühler ebenfalls
vor möglichen Durchzug schützen, welcher
durch ein Fenster, eine Tür oder eine kühle Aus-
senwand verursacht werden könnte.
Fühlerkabel: Das Fühlerkabel darf nicht in
Kabeln oder Leitungsbündeln gemeinsam mit
anderen Stromkreisen geführt werden. Es sollte
verhindert werden, dass das Kabel parallel zu
anderen Wechselstromleitungen eingezogen
wird, welche Störsignale auf das Fühlersignal
induzieren und damit die Funktion des Thermo-
states stören könnten.
ABBILDUNGEN
Abb. 1 Anschlussschema
Abb. 2 Fühlertabelle
Abb. 3 Abmessungen
Deutsch
English
English
APPLICATION
ATE 50 is a compact thermostat for control of
the temperature in industrial systems.
PRODUCT PROGRAMME
ATE 50 with scale range -10/+50 °C
Accessories
Sensors:
ATF 5 : NTC sensor for outdoor temperarure.
AF 5-2,5 : NTC sensor for pipes and machine
parts
FUNCTION
The ATE 50 is an ON/OFF thermostat with ad-
justable dierential temperature (see technical
data) for control of temperature. When the sen-
sor temperature is below the temperature set
-dierential the potential-free relay is activated
(closes between terminal 4 and 5) and heating is
switched on. Red LED indication.
When the sensor temperature exceeds the set
temperature +dierential the relay breaks be-
tween terminal 4 and 5 and the heating element
is switched o, and the red LED turns o.
As the ATE 50 is supplied with a change-over
relay the ATE 50 may also be used as a cooling
thermostat, if a cooling element is connected
between terminal 3 and 5.
CE MARKING
According to the following standard:
LVD/EMC: EN 60730-2-9.
The product may only be energised when the
entire installation meets the current directive
requirements.
When the product is installed according to this
instructions guide and the current installation
guidelines, it is covered by factory guarantee.
If the product has been exposed to damage e.g.
in transport, it must be checked and overhauled
by qualified sta before the product is con-
nected to the power.
TECHNICAL DATA
Supply voltage ......... 230V AC ±10%, 50-60 Hz
Max. fuse .....................................................10A
Output relay .................................. S.P.C.O. 10A
Dierential - adjustable ....................... 0.3-6 °C
Operational temperature ..................... 0/+50 °C
Power consumption ................................... 3VA
Weight ......................................................170 g
Dimensions (HxWxD) .................. 86x36x58 mm
Housing .....................................................IP 20
Temperature sensor .................. NTC-thermistor
CLASSIFICATION
The product is a Class II product (reinforced
insulation) and the product must be connected
to the following conductors:
1) Phase (F/L1)
2) Neutral (N)
TEMPERATURE SETTING
The ATE 50 has a scale range of -10/+50 °C
The thermostat is supplied with a LED which is
red when heating is on. The thermostat is set on
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG ATE 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG ATE 50 in the language / languages: German as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info