800003

Adler AD 7031 Manual

4
Zoom out
Zoom in
Previous page
1/44
Next page
19. The device is intended for cleaning hard, flat and dry surfaces indoors.
20. Devices must not be used for cleaning liquids, smoldering, burning, wet or corrosive
waste.
21. Before turning on the device you should remove from all surfaces to be cleaned fragile
or small items as well as any rugs and carpets that do not protrude above the lower edge
of the casing. You must remove any element that may become trapped by brushes as
cables or cords. You should also secure all recesses, stairs, balconies and an undesirable
from accidentally entering the robot.
22. All hanging objects like wires or cords can cause malfunctions of work by influencing
the light sensor.
23. Do not stand, sit or place anything on the device.
DESCRIPTION OF THE DEVICE
1. Turning wheel 2. Drive wheels 3. Side brush
4. Main brush 5. Main brush release button 6. Cover of dirt container
7. Dirt container opening button 8. Battery cover 9. Switch ON/OFF
10. Charging socket 11. Carrying handle 12. The barriers sensor
13. Working mode buttons 14. LED indicator of the problem 15. LED charging indicator
16. Light sensor
CHARGING AND BATTERY REPLACEMENT
Plug the charger into a wall outlet, then insert the small plug it into the charging socket (10) in the device. The first charge should last at
least 4 hours, and the next charges should last until the device is fully charged. A sound signal indicates the start of charging. The LED
(15) flashes throughout the charging time and after it, it stops flashing and signals the stop by sound signal. To replace the battery,
follow the drawing D.
USING THE DEVICE
1. Place the robot in the middle of the room to be cleaned.
2. Turn the robot using switch (9). Select mode by pressing the appropriate button (13).
3. The robot starts working. To stop press the button (9 or 13).
4. If brush (4) will be blocked, robot will stop work and problem indicator LED (14) will flash. You should then clean the brush.
5. If the robot turns off during operation and charging LED (15) will flash you should charge the battery.
6. If the robot turns off during operation and both LEDs start flashing you should then hold the switch (9) for 5 seconds to turn off the
robot, and then turn it on again. After each such operation robot should be cleaned in accordance with section Cleaning.
7. After finishing of work, the robot turns off. You should then using button (7) open the dirt container and empty it. You should also clean
both brushes.
CLEANING AND MAINTENANCE
1. Before cleaning robot, turn off and disconnect it from the charger.
2. Wipe the case with a dry cloth.
3. Remove all hair from brushes. Displacement/replacement of brushes is shown on pictures B and C.
4. Clean the turning wheel housing with brush, being careful not to damage the cables. Displacement/ replacement of turning wheel is
shown on picture A.
TECHNICAL DATA
Power supply: 220-240V ~ 50Hz
Power: 7W
The volume level of the Lion 65 dB
Maximum efficient worktime: 90 min.
4
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
effect the environment. Do not dispose this appliance in the common waste bin.
DEUTSCH
ALLGEMEINE SICHERHEITSVORSCHRIFTEN LESEN SIE AUFMERKSAM WICHTIGE
ANWEISUNGEN BEZÜGLICH DER SICHERHEIT DER BENUTZUNG BEWAHREN SIE
DIESE FÜR DIE ZUKUNFT AUF
Bei Verwendung des Gerätes zu gewerblichen Zwecken werden die Garantiebedingungen
geändert.
1.Vor dem ersten Gebrauch, die Bedienungsanleitung lesen und die dort angegebenen
Hinweise beachten. Der Produzent trägt keine Verantwortung für Schäden, die aufgrund von
bestimmungswidriger Nutzung oder unsachgemäßer Bedienung entstanden sind.
2.Das Gerät ist nur für den Hausgebrauch verwendet. Verwenden Sie es nicht für andere
Zwecke als den bestimmungsgemäßen Gebrauch.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adler AD 7031 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adler AD 7031 in the language / languages: English, German, Dutch, French, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2.62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info