736192
4
Zoom out
Zoom in
Previous page
1/68
Next page
16. Do not insert fingers or any other objects into blender's cup when the blender is on.
17. In order to avoid injuries handle the blades carefully.
18. Watch out for long hair, scarves, neckties hanging above the cup and operating
components of device.
19. For safety reasons use only original accessories and spare parts intended for particular
blender type, available at authorised service centre.
20. Handle the blades with extreme care while disassembling accessories. The blades can
cause cuts.
21. Do not wash any blender parts in dishwashers.
22. Change the accessories only when the device is switched off. Disconnect the device
from the power.
23. Do not put any products other than food and liquids in the blender cup. Do not put hot
products in the cup.
24. The device is not suitable for whipping egg whites, kneading dough or grinding meat.
Don't use aggressive detergents to clean the housing, as it may remove the informational
graphic symbols such as: scale, signs, safety marks, etc.
25. Do not start the empty mixing cup, without product inside.
26. MAXIMUM PERIOD OF CONTINUOUS BLENDER OPERATION IS 3 MINUTES. After
3 minutes of continuous operation stop the device and wait couple of minutes before
restarting.
DEVICE DESCRIPTION
1A – Interlock switch 1B – Lid 1C – Jug 1D – Main body
1E – Speed adjustment knob 1F – Pulse 1G –Blade base
DEVICE OPERATION
Before first use:
1. Remove all stickers from the housing, jug and cover of the blender.
2. Wash the jug and the lid in warm water with washing-up liquid, rinse thoroughly, dry the inside and outside of the jug.
ASSEMBLY / DISASSEMBLY
1. Place the blade assembly (2A) and gasket (2B) on the blade base (2C) and next add the clutch (2D) from the bottom, then screw
together all parts tightly by turning in the left side until it is firmly in place (Picture 2).
2. Place the jug upside down on a flat, stable surface, and then place the already assembled blade base (1G) to jug by turning it in the
left side until it is firmly in place (Picture 3).
3. Disassemble in reverse order in relation to assembly.
USEAGE:
1.Put the blender main body (1D) on stable, level surface.
2. Make sure the speed adjustment knob (1E) is set to the OFF position.
Knob marking: P – Pulse 0 – OFF 1 – Slower speed 2 – Faster speed
3. Place the jug (1C) on main body (1D), the interlock switch (1A) will reach correct position to operate. (Picture 1)
4. Remove lid (1B) from the blender jug (1C), put in the ingredients to be mixed. In order to avoid overflow, the level of ingredients in the
jug should not exceed ¾ of jug's height. Close the lid.
5. Connect the power plug to the power outlet.
6.Turn the device on by pressing Pulse button or by rotating speed adjustment knob (1E) to slower speed or faster speed.
NOTICE: During mixing always hold the jug (1C) with hand.
7.After the mixed products have proper consistence, turn the device off by rotating speed adjustment knob (1E) to off position. Wait until
the blades stop. Remove the power plug from the power outlet. Remove the lid.
NOTICE: Do not allow continuous operation of blender for longer than 3 minutes.
NOTICE: The pulsation operation mode, when the Pulse setting is switched, is used for a momentary mixing with maximum speed.
CLEANING AND MAINTENANCE
Make sure that the device is disconnected from the power.
1. Disassemble the jug (1C) from the blade base (1G), next disassemble all parts shown on Picture 2 in reverse order in relation to
assembly.
2. Wash the jug, lid and parts shown on Picture 2 in water with washing-up liquid. Rinse thoroughly and dry all parts.
4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adler AD 4076 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adler AD 4076 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 2,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info