756348

Abus mk4100 Manual

2
Zoom out
Zoom in
Previous page
1/6
Next page
UK
MK4100
Installation instructions – Magnetic contact for gates and doors
Introduction
Top-class, heavy-duty contact for gates and doors. Extremely robust aluminium design – highly-resistant to breakages (e.g.
when driven over by forklifts). VdS Class C certified.
Advantages of the magnetic contacts
High resistance to environmental conditions
Very large switching intervals
Extremely high resistance to wear
Simple installation
Installation
Installation is primarily made on roll-up, sliding and tilting gates and doors.
Before installation, determine the installation location so that the door contact and magnet can be fitted as shown in fig. 2.
The contact casing is fitted on the floor (a flat mounting surface is necessary).
Otherwise, only screws made of non-ferromagnetic materials may be used.
The weatherproof and mechanically stable construction of the contact casing protects the switching mechanism from
damage when driven over by vehicles with rubber tyres. To protect the product from greater loads, it must be embedded
into the ground.
The four-core cable is protected by a stainless steel protective sleeve. Two hose clips with screws and wall plugs are
included in the installation set for laying the metal sleeve properly away from the door or gate area.
When fitting the magnet casing, note the position of the two screw-holes on the contact casing, as shown in fig. 1. These
two holes determine the exact lateral position of the magnet relative to the contact.
The spacing between the contact casing and magnet casing should measure approximately 5-25 mm (as shown in the
diagram). If ferromagnetic materials are present in the immediate vicinity, then the switching areas must be specially
determined. The magnet should always be fitted in the middle of the non-operational area whilst adhering to VdS fitting
guidelines.
During installation, pay attention to the movement tolerance of the movable fitting surface for the magnet casing.
After installation is completed, the electrical functions on the contact must be checked (e.g. ohmmeter or circuit tester).
Warning:
The magnet loses some of its field strength if exposed to intense
heat or vibrations. This can also happen if it is placed near another
magnet and like poles are placed together.
Technical data:
Housing material: Aluminium
Cable: 2 m (double-insulated: 4 x 0.14 mm²)
Connections: NC, max. contact capacity
60 V DC / 300 mA / 3 W
Temperature with fixed cables: -25 °C to +70 °C
Temperature with movable cables: -5 °C to +50 °C
Protection class: IP 65
Optimal spacing between sensors: 5-25 mm
VdS Class B: G 198067
Functional diagram
Floor
Magnet switch
Fig. 2
Fig. 1
Door
Floor
Magnet switch
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abus mk4100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abus mk4100 in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info