42029

9ZAP 9Z World Champion Model 2 Manual

26
Zoom out
Zoom in
Previous page
1/29
Next page
23
DESCRIPTION
O
F NEW FUNCTIONS
(6) Call ATV from the condition (CND) items and decide AU2 operation width.
-At this time, operate the VR set using function control (FNC), or SW "C", over its full stroke and decide the
operation width while being careful that unreasonable force is not applied to the linkage.
(7) After setting the operation width, finally decide the function control (FNC) of
item (2) above.
-For switch selection, select 'NULL' so that the fuel mixture function is not performed by switch operation. (Per-
form the fuel mixture function by switch operation by setting the fuel mixture control system to ACT.)
3 Operating the fuel mixture function
(1) Call the model menu (MDL) and select "FMC" fuel mixture function.
(2) Set the fuel mixture control system to "ACTIVE".
-So that the fuel mixture control system is operated with AU2 (CH8) as mixture (needle) control.
-When AU2 (CH8) FUNCTION is "HIGH", the high side needle can be controlled by moving the throttle stick
from medium speed to high speed. When AU2 (CH8) FUNCTION is made "TRIM", the fuel mixture function
changes to entire curve parallel movement. Normally use the fuel mixture function at the "HIGH" setting.
(3) Preset the setting VR to the center position.
(4) Set the throttle stick and throttle trimmer to the maximum slow side (+50~+100)
and check if the mixture control arm moves to the stopper position and the fuel sup-
ply is completely shut off. (The trimmer position depends on the mixture curve set-
ting.)
-At the end of confirmation, return the throttle trimmer to the neutral position.
(5) After starting the engine, use the throttle trimmer to adjust the idling speed, the
same as in the past.
CAUTION: After connecting the linkage, recheck the operation direction and operation
amount of each part.
4 Throttle cut
(1) Call the model menu (MDL) and select throttle cut "CUT".
(2) Set MODE to "ACTIVE".
(3) Set THR POSITION.
-This sets the range over which throttle cut can be turned on.
(4) Set the cut switch.
-Select "SWT" and set the switch to be used.
(5) Set the throttle cut rate.
-When the cut switch is turned on, the cut function is performed.
Adjust the rate in the ON state.
-Set the throttle and mixture rates separately. Adjust the throttle and mixture full close position with each rate
item. (The operation direction is the direction in which the needle is closed in the (-) direction.)
-The (AU2) side is the mixture cut setting.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 9ZAP 9Z World Champion Model 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 9ZAP 9Z World Champion Model 2 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info